– 156 –
Chapter 9 Maintenance — Warning system
Warning system
If an error is detected immediately after the camera is turned on or during operation, the viewfinder, LCD monitor, and tally lamp indicate the error. Deal
with the error by following the indications.
Cases indicated by error codes
Error code
Display
Description
Behavior and cause
[E-30]
[TURN POWER OFF]
[P2 CARD]
An error occurred in the camera built-in memory
because the microP2 memory card being accessed
was ejected.
f
Tally lamp flashes four times per second.
f
Cannot operate.
f
Follow the message to turn off the power once and
turn on the power again.
f
Ensure that there is no error in the clips on the
ejected card, and restore the clips as necessary.
[E-31]
[TURN POWER OFF]
[SYSTEM MODE]
System mode error occurred.
f
Tally lamp flashes four times per second.
f
Cannot operate.
f
Follow the message to turn off the power once, turn
on the power again, and check that there is no error
display.
[E-33]
[SYSTEM ERROR]
[CAMERA]
Camera unit error occurred.
f
Tally lamp flashes four times per second.
f
The operation stops.
f
Contact your dealer.
[E-35]
[SYSTEM ERROR]
[CODEC]
Codec control error occurred.
f
Tally lamp flashes four times per second.
f
The operation stops.
f
Contact your dealer.
[E-36]
[SYSTEM ERROR]
[P2 SYSTEM]
P2 system error occurred.
f
Tally lamp flashes four times per second.
f
The operation stops.
f
Contact your dealer.
[E-37]
[SYSTEM ERROR]
[P2CS]
P2CS microcomputer error occurred.
f
Tally lamp flashes four times per second.
f
The operation stops.
f
Contact your dealer.
[E-39]
[SYSTEM ERROR]
[INITIALIZE]
Video initialization error occurred.
f
Tally lamp flashes four times per second.
f
The operation stops.
f
Contact your dealer.
[E-64]
[SYSTEM ERROR]
[FRAME SIGNAL]
(or no display)
Reference signal error occurred.
f
Tally lamp flashes four times per second.
f
The operation stops.
f
Contact your dealer.
Cases indicated by error messages
During recording/playback
Display
Description
Behavior and cause
[AUTH NG CARD] (slot number)
CPS authentication of microP2 memory card has failed.
The microP2 memory card whose CPS authentication
failed cannot be recorded or played back.
f
The current operation will continue.
f
Select [AUTHENTICATE] in the main menu
→
[CLIP],
and enter the password.
[BACKUP BATT EMPTY]
Displays any reduced voltage detected on the backup
battery in the internal clock when the power is turned
on.
f
The current operation will continue.
f
Charge the built-in battery.
[SET DATE AND TIME]
Displayed when the internal clock setting is reset.
f
The current operation will continue.
f
Set the date/time of the internal clock. (page 36)
[CARD ERROR] (slot number)
Displayed when a data error caused by the microP2
memory card has occurred during the recording.
Displayed after recording stops until the next operation.
Displayed for three seconds when the playback has
stopped due to error of the microP2 memory card
during the playback.
f
If the error occurs during recording, the tally lamp
flashes four times per second for approx. three
seconds after recording stops.
f
The tally lamp does not flash when an error occurs
during playback.
f
The operation will stop.
f
Once it has stopped, the microP2 memory card
where the error has occurred is write-protected.
Replace the microP2 memory card in the slot where
the error has occurred.
[DIR NG CARD] (slot number)
The directory position is not correct.
f
The current operation will continue.
f
Make a card backup immediately and format the card
to use it again.
[FAN STOPPED]
Displayed when the fan motor stops.
f
The current operation will continue.
f
If the fan has stopped with error, stop using the
camera immediately and consult your dealer.
f
If the fan has stopped, temperature of the camera
will rise. Therefore, do not use the camera for a long
period of time.
[HIGH TEMPERATURE]
The temperature inside the camera is higher than that
of the normal conditions.
f
The current operation will continue.
f
Turn off the power of the camera, turn it on again,
and check recording and playback operations. If the
problem persists, consult your dealer.
[PB INTERMITTENT] (slot number)
Playback is interrupted on the SDHC/SDXC memory
card. A card whose playback performance cannot be
assured is inserted.
f
The current operation will continue.
f
It is recommended to use the microP2 memory card.
Summary of Contents for AJ-PX230 Series
Page 12: ...Before using the camera read this chapter Chapter 1 Overview ...
Page 153: ...Maintenance of the camera or frequently asked questions are described Chapter 9 Maintenance ...
Page 161: ...This chapter describes the specifications of this product Chapter 10 Specification ...
Page 169: ...Web Site http www panasonic com Panasonic Corporation 2016 ...
