42
Error messages (continued)
E-64
S REEL ROTA
TOO FAST
If the supply reel motor speed is abnormally high, the error
number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-67
T REEL ROTA
TOO FAST
If the take-up reel motor speed is abnormally high, the error
number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-69
T REEL
TORQUE ERR
If excess torque being applied to the take-up reel motor is
detected, the error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-70
S REEL
TORQUE ERR
If excess torque being applied to the supply reel motor is
detected or an abnormal current flowing to the current
detection resistor is detected, this error number flashes on
the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-71
CAP TENSION
ERROR
If abnormal tension at the supply side is detected in the
capstan mode, the error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-72
REEL TENSION
ERROR
If abnormal tension at the supply side is detected in the reel
mode, the error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-73
REEL DIR
UNMATCH
If the take-up reel motor has rotated in the reverse
direction, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-74
DRUM TORQUE
ERROR
If excess torque being applied to the cylinder motor is
detected, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-78
M-IF COMM
ERROR
If a problem has been encountered in communication
between the servo microcomputer and mechanism relay
board, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
Monitor display
Description
VTR operation
Corrective action
Note:
Consult your dealer if the error message is still displayed even after restarting the unit.
E-59
DRUM ROTA
TOO SLOW
If the cylinder motor speed is abnormally low, this error
number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
E-60
DRUM ROTA
TOO FAST
If the cylinder motor speed is abnormally high, this error
number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
E-61
CAP ROTA
TOO SLOW
If the capstan motor speed is abnormally low, the error
number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
STOP
STOP
E-57
S-FF/REW
TIMEOVER
If the start or end processing operation is not completed,
this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-55
UNLOAD ERROR
If the tape has not been taken up during unloading, this
error number flashes on the display.
Set the POWER switch to
OFF and then to ON again.
STOP
E-53
WINDUP ERROR
If there is an abnormally large discrepancy between the
amount of tape taken up by the take-up reel and the
amount of tape supplied by the supply reel while the tape is
traveling after the total amount of the tape begins to be
detected, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
Summary of Contents for AJ-SD255 - Professional Editing Video Cassete recorder/player
Page 45: ...45 MEMO ...
