98
8-3-8
SKIN TONE DTL
8-3-9
KNEE/LEVEL
<Note>
The items indicated by
are the setting items for PAINT MENU
SW(
) R/W in the <SD CARD R/W SELECT> screen. The items
without
are the setting items for PAINT MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved
Adjustable
Range
Remarks
SKIN TONE
DTL
ON
OFF
Set the skin tone DTL to ON or OFF.
S C U F E
SKIN TONE
ZEBRA
ON
OFF
ON/OFF switching for ZEBRA within the
SKIN TONE range.
S C U F E
SKIN DTL
CORING
0
:
5
:
7
Adjust the effect of SKIN TONE DTC
CORING.
S C U F E
SKIN TONE
GET
Used when obtaining the target hue for
SKIN TONE DTL. Align the centre marker
and the target object with each other.
– – – – –
Y MAX
000
:
190
:
255
Set the maximum value of the brightness
signal to which SKIN TONE effect is
enabled.
S C U F E
Y MIN
000
:
010
:
255
Set the minimum value of the brightness
signal to which the SKIN TONE effect is
enabled.
S C U F E
I CENTER
000
:
022
:
255
Set the centre position on the I axis (the
area where SKIN TONE is enabled).
S C U F E
I WIDTH
000
:
010
:
255
Set the area width where SKIN TONE is
enabled along the I axis above and below
the I CENTER.
S C U F E
Q WIDTH
000
:
005
:
255
Set the area width where SKIN TONE is
enabled along the Q axis above and below
the I CENTER.
S C U F E
Q PHASE
–128
:
+000
:
+127
Set the phase in the area where SKIN TONE
is enabled based on the Q axis.
S C U F E
R-Y
B-Y
Q-WIDTH
I-WIDTH
Q-PHASE
I-CENTER
Y
Y-MAX
Y-MIN
0
+ direction
= SKIN TONE AREA
Items/
Data Saved
Adjustable
Range
Remarks
MASTER PED
–200
:
+020
:
+200
Set the master pedestal.
S C U F E
MANUAL
KNEE
ON
OFF
Set the mode when the AUTO KNEE switch
is OFF. The KNEE POINT/SLOPE set value
is enabled when this setting is ON.
S C U F E
KNEE POINT
70.0%
:
85.0%
:
107.0%
Set the KNEE POINT position in 0.5% steps.
S C U F E
KNEE SLOPE
00
:
50
:
99 (98)
Set the KNEE SLOPE.
0 setting is equal to KNEE OFF.
<Note>
The adjustable range when using the AJ-
EC3E is from 00 to 98.
S C U F E
WHITE CLIP ON
OFF
Set the WHITE CLIP feature to ON or OFF.
The WHITE CLIP LVL set value is enabled
when this setting is ON.
S C U F E
WHITE CLIP
LVL
90%
:
105%
:
109%
Set WHITE CLIP LEVEL.
S C U F E
A.KNEE POINT 80%
:
85%
:
107%
Set the AUTO KNEE POINT position in
0.5% steps. This setting is enabled when the
OUTPUT/AUTO KNEE selector switch is set
to CAM.AUTO KNEE ON.
S C U F E
A.KNEE LVL
100
:
105
:
109
Set the AUTO KNEE LEVEL.
S C U F E
A.KNEE
RESPONSE
1
:
4
Set the AUTO KNEE response speed.
The smaller the setting value, the faster the
response speed.
S C U F E
– direction
Summary of Contents for AJ- SPX800E
Page 117: ...117 9 MEMO ...
