109
8
8-3-12
CAMERA SETTING
ZEBRA Pattern Display
<Note>
All items in CAMERA SETTING are setting targets of the item
PAINT MENU SW(
) R/W in the <SD CARD R/W SELECT>
screen.
8-4
VF
8-4-1 VF DISPLAY
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved
Adjustable
Range
Remarks
DETAIL
ON
OFF
Set the DTL (H, V) to ON or OFF.
S C U F E
2D LPF
ON
OFF
ON/OFF switching for the two-dimensional
LPF that reduces cross-color.
S C U F E
HIGH COLOR
ON
OFF
ON/OFF switching for the HIGH COLOR
mode, which enhances the color dynamic
range.
S C U F E
GAMMA
ON
OFF
Set the gamma circuit to ON or OFF.
S C U F E
TEST SAW
ON
OFF
Switch the test signal ON or OFF.
S C U F E
FLARE
ON
OFF
Set the flare correction to ON or OFF.
S C U F E
H-F COMPE.
ON
OFF
ON/OFF switching for the H-F COMPE
mode, which enhances the DTL in the high-
frequency range.
S C U F E
SPOT
OFF
ON
109%
0%
ZEBRA 2
DETECT
ZEBRA 2
ZEBRA 1
DETECT
Video Level
Items/
Data Saved
Adjustable
Range
Remarks
DISP
CONDITION
NORMAL
HOLD
NORMAL:
Display status constantly.
HOLD:
Display status only when the
MODE CHECK switch is pressed.
– C U F E
DISP MODE
1
2
3
Set the DISP MODE.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4 Display
Modes and Setting Changes/adjustment
Result Messages] for more information.
– C U F E
VF OUT
Y
NAM
R
G
B
Select the VF output.
Y:
Brightness signal
NAM:
Output signal with the highest level
among R, G, and B signals.
R:
Rch signal
G:
Gch signal
B:
Bch signal
– C U F E
VF DTL
0
:
3
:
5
Select the VF DTL.
Additionally enhance the DTL for the VF
signal. 0 setting is the same DTL as the
primary scan lines.
– C U F E
ZEBRA1
DETECT
0%
:
70%
:
109%
Set the ZEBRA1 detection level (IRE value).
– C U F E
ZEBRA2
DETECT
0%
:
85%
:
109%
Set the ZEBRA2 detection level (IRE value).
– C U F E
ZEBRA2
ON
SPOT
OFF
Set the ZEBRA2 to ON, OFF, or SPOT.
– C U F E
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%
Set the camera incoming light volume at
which to display LOW LIGNT.
– C U F E
ECU MENU
DISP.
ON
OFF
Set the menu display on the VF to ON or
OFF when the ECU is connected.
– C U F E
50M
INDICATOR
ON
OFF
Set the 50M recording indication to ON or
OFF.
– C U F E
MARKER/CHAR
LVL
50%
60%
70%
80%
90%
100%
Adjust the brightness of markers and
characters displayed on the VF.
– C U F E
#,52:''PINKUJDQQMࡍࠫ㧞㧜㧜㧡ᐕ㧟㧞ᣣޓ᳓ᦐᣣޓඦᓟ㧡ᤨ㧞㧜ಽ
