Control reference guide (continued)
– 13 –
When the AUDIO MIX switch
is at the [3&4]
setting, the setting is switched by one step in the
sequence of A
→
→
B
→
→
C each time the REC CH2/4
button is pressed.
(
ON; OFF)
CH1/3
CH2/4
A
The CH4 signals are recorded on
CH4.
B
The CH3+CH4 signals are recorded
on CH4.
C
The CH3 signals are recorded on
CH4.
AUDIO MONITOR SELECT (L/R)
Switch the audio signal to be output to the MONITOR
L/R connectors.
Each time you press the L button, the signals output to
the MONITOR L connector switches: [CH1]
→
[CH2]
→
[CH3]
→
[CH4].
Each time you press the R button, the signals output to
the MONITOR R connector switches: [CH1]
→
[CH2]
→
[CH3]
→
[CH4].
You can check which signal is currently selected by
seeing which of the L/R lamps in the level meter is lit.
MONITOR MIX button
This button is used to select the mixed signals which are
to be output to the MONITOR L and R connectors.
Each time the MONITOR SELECT L button is pressed
while this button is held down, the signals to be output to
the MONITOR L connector change in the following
sequence: [CH1+CH2]
→
[CH3+CH4]
→
[CH1+CH3]
→
[CH2+CH4]
→
mixing release.
The mixed signals to be output to the MONITOR R
connector are changed in the same way by the
MONITOR SELECT R button.
METER (FULL/FINE) selector button
Select the scale display for the audio level meter (See
page 14).
FULL mode:
The standard scale (–
∞
to 0 dB).
FINE mode:
Scale in 0.5 dB increments.
“
” indicates the standard level of –20 dB (–18 dB),
and each of the dots “
” indicates a 1 dB scale
increment.
Headphone jack and volume control
Connect stereo headphones to monitor the sound during
recording or playback.
ENC CONTROL (REMOTE/LOCAL)
Select whether encoder control is to be done on the
memory card recorder or another deck.
REMOTE :
Encoder control is done remotely.
LOCAL
:
Encoder control is done on the memory card
recorder.
VIDEO LEVEL dial and switch
When ENC CONTROL is set to [LOCAL], you can adjust
the video output level.
When set to [PRESET], the video output level is a unity
value (0 dB).
When set to [MANUAL], you can adjust the level with
the dial.
CHROMA LEVEL dial and switch
When ENC CONTROL is set to [LOCAL], you can adjust
the chroma level.
When set to [PRESET], the chroma level is a unity value
(0 dB).
When set to [MANUAL], you can adjust the level with the dial.
SET UP LEVEL dial and switch
When ENC CONTROL is set to [LOCAL], you can adjust
the setup level.
When set to [PRESET], the setup level is a unity value
(0 IRE).
When set to [MANUAL], you can adjust the level with the dial.
HUE LEVEL dial and switch
When ENC CONTROL is set to [LOCAL], you can adjust
the hue.
When set to [PRESET], the hue is a unity value (0 °).
When set to [MANUAL], you can adjust the hue with the dial.
TC REGEN/PRESET switch
REGEN:
The internal time code generator synchronizes with the
time code read by the time code reader from the card.
Select whether to make TC or UB the REGEN in
Setup Menu No. 503 (TCG REGEN).
PRESET:
You can preset with the control panel or remote
control.
TC REC RUN/FREE RUN switch
REC RUN:
The time code runs only while recording.
If REGEN/PRESET is set to [REGEN], the time code
runs constantly.
FREE RUN:
The time code runs when the memory card recorder is
on, irrespective of the operating mode.
DIAG button
Press to show information about the memory card
recorder. Press again to return to the previous display.
(However, the button and display will not function while
thumbnails are displayed.)
The HOURS METER information, WARNING
information and UMID information are shown as the
unit's information.
Press the SEARCH button to switch among the three.
HOURS METER shows the memory card recorder’s
serial number, the number of hours it has been on, and
the number of times it has been switched on and off.
WARNING shows warnings.
AUDIO VOL SEL switches
REC/PB switch
REC: The recording level can be adjusted using the
audio level controls.
PB: The playback level can be adjusted using the
audio level controls.
UNITY/VAR switch
UNITY: The audio signals are recorded and played
back at a fixed level regardless of the positions
of the audio level controls.
VAR: The audio signals are recorded and played back
at the levels adjusted using the audio level
controls.
Audio level controls
Use these to adjust the recording and playback levels
of the audio signals (CH1/CH2/CH3/CH4).
