74
Screen displays (continued)
19 Zoom position display
(In CAM mode: Page 48)
Displays the zoom position with Z00 (maximum
wide-angle) - Z99 (maximum zoom).
You can switch between displaying and
•
not displaying this information by selecting
[ZOOM & FOCUS]
→
[ON] or [OFF] in the
[DISPLAY SETUP] setup menu.
20 SDI through output display
(In SDI mode: Page 87)
When [SDI EE SEL]
→
[THROUGH] is
selected in the [AV OUT SETUP] setup menu,
“THROUGH” is displayed.
There is no output to external devices.
•
21 Focus control information display
(In CAM mode: Pages 50, 83)
Displays the focus control information with
99 - 00.
In the auto focus mode,
AF
is displayed, and
in the manual focus mode,
MF
is displayed.
When the macro control function is operating,
the black and white of
AF
or
MF
are
displayed in reverse.
95
(Focal distance: infinity)
:
00
(Focal distance: approx. 5 cm)
Depending on the zoom position, the macro
•
range may not be enabled. Also, depending
on the zoom position, the lower limit value of
the macro range may be different.
You can switch between displaying and
•
not displaying this information by selecting
[ZOOM & FOCUS]
→
[ON] or [OFF] in the
[DISPLAY SETUP] setup menu.
22 Index/shot mark recording display (Page 42)
MARK ON: Displayed when a shot mark is
added.
MARK OFF: Displayed when a shot mark is
canceled.
INDEX: Displayed when an index is added.
“INVALID” is displayed if an index or shot
•
mark cannot be added.
23 Gain display (In CAM mode)
Displays the current gain value.
You can switch between displaying and
•
not displaying this information by selecting
[OTHER DISPLAY]
→
[ON] or [OFF] in the
[DISPLAY SETUP] setup menu.
24 AWB information display
(In CAM mode: Pages 41, 53)
Displays information for white balance.
ATW:
When ATW is set
P3.2K/P5.6K:
When preset is used
W.SET:
When white balance is adjustable
LOCK:
When ATW is locked
You can switch between displaying and
•
not displaying this information by selecting
[OTHER DISPLAY]
→
[ON] or [OFF] in the
[DISPLAY SETUP] setup menu.
25 Optical Image Stabilizer display
(In CAM mode: Page 49)
Displayed when the Optical Image Stabilizer
is [ON].
You can switch between displaying and
•
not displaying this information by selecting
[OTHER DISPLAY]
→
[ON] or [OFF] in the
[DISPLAY SETUP] setup menu.
26 Key lock display (Page 46)
Displayed when the operation buttons are
disabled.
When the remote control (optional) is
•
connected to the REMOTE jack of the
portable recorder, recording and zoom
operations with the remote control are
available even during key lock.
27 Remaining battery capacity display
When using Panasonic-manufactured batteries
that are compatible with the portable recorder,
the remaining battery capacity is displayed in
minutes. The time remaining is displayed after
a brief pause.
As the battery capacity decreases, the
•
display changes as follows:
→
→
→
→
.
is displayed in red when less
than 3 minutes are remaining, and
flashes when the battery has run out.
The remaining battery capacity may not be
•
displayed correctly when the battery is used
in high or low temperatures, or when it has
not been used for a long time. To ensure that
the remaining battery capacity is displayed
correctly, use a fully-charged battery until it
runs out, and then charge the battery again.
(Even if you do this, the remaining battery
capacity may still not be displayed correctly
if the battery has been used for long periods
in high or low temperatures, or if the battery
has been recharged a large number of
times.)
Summary of Contents for AVCCAM AG-HMR10
Page 106: ...E P ...
