Q’ty
Q’ty
Item
No.
E
N
G
L
I
S
H
51
E
N
G
L
I
S
H
52
CQ-DVR7000U
CQ-DVR7000U
70
71
Wiring Connections
❐
Accessories used for wiring
2
Power Amplifier Unit
1
?
Power Connector
(for Main Unit)
1
>
12 pin audio connector
1
POWER DISPLAY UNIT RGB
CENTER
SPEAKER
(EAB-CF2)
(
s
)
(
r
)
(
s
)
(
r
)
(
s
)
(
r
)
(
s
)
(
r
)
Pre-out (Front)
Pre-out (Rear)
:
Power Connector
(for Main Unit)
;
Power Connector (for Power Amplifier Unit)
2
Power Amplifier Unit
Pre-out (Center)
Pre-out (Sub Woofer)
Video Output Cord
Changer Input Cord
AUX Input Cord
CQ-DVR7000U
CY-VM1500EX
Controller Unit
Yellow
Black
Fuse (15 A)
Battery Lead
Speaker
Lead
LEFT SPEAKER
(FRONT)
LEFT SPEAKER
(REAR)
RIGHT SPEAKER
(FRONT)
RIGHT SPEAKER
(REAR)
Yellow
White
Gray
Green
Violet
Power Connector
(Supplied to CY-VM1500EX)
Changer Control Connector
Radio Antenna Input
Dual Changer
Control Cord
External Amplifier
Control Power Cord
(to external amplifier)
Motor Antenna
Relay Control
Moves antenna up
and down.
Video Control Cord
(This cord is not used.)
(VIDEO-OUT)
(FRONT L)
(FRONT R)
(REAR L)
(REAR R)
(BATTERY 15 A)
(AUX-IN)
(NAVI MUTE)
Orange
Orange/White Stripe
Blue/Yellow Stripe
Red
Yellow
Black
Blue/White
Stripe
Brown/White
Stripe
Dark Blue
Green/Yellow
Stripe
(VIDEO-CONT)
(ILLUMINATION)
(PARKING BRAKE)
(ACC)
(BATTERY 5 A)
(ANT-CONT MAX 0.1A)
(TWIN CD
•
C-CONT)
(CH
.
C
•
IN)
(AMP-CONT MAX 0.1A)
Red (R)
White (L)
Fuse (5 A)
Navi Mute Cord
Connect the Navi Mute Cord to
the Navi Mute Cord on a Panasonic
navigation system (In future use).
Illumination Cord
Connect the Illumination Cord to
the power source that powers
the car’s small lights.
Parking Brake Cord
For safety’s sake, and to prevent accidents,
the Parking Brake Cord must be connected.
(
➡
page 73)
Power Lead (ACC or IGN)
To ACC power,
_
12 V DC
To the car battery,
continuous
_
12 V DC
White/
Black
Stripe
Green/Black
Stripe
To a clean, bare metallic
part of car chassis
Ground Lead
To a clean, bare metallic part of car chassis
To the car battery continuous
_
12 V DC
Violet/Black
Stripe
Gray/Black
Stripe
RCA Cord (Option)
Red (R)
White (L)
Resistor (1k
Ω
)
Subwoofer
(CJ-SW46)
Red (R)
White (L)
(REAR AUDIO-OUT)
REAR AUDIO-OUT Cord
External Amplifier
(CY-M7052)
External Amplifier
(CY-M7052)
>
12 pin audio connector
Connect this cord
when the monitor
is to be installed
on the back seat.
(R)
(L)
(L)
(R)
RCA Cord (Option)
Control Unit Connector
Amplifier Unit Connector
L
L
L
L
R
R
R
R
L : White
R : Red
Battery Lead
Ground Lead
CQ-DVR7000U
❐
Wiring diagram:
≥
This product is designed to operate of a 12 V, negative ground battery system.
≥
To prevent damage to the unit, be sure to follow the connection diagram below.
≥
Remove approx. 1/4” (5 mm) of protective covering from the ends of the leads before connecting.
≥
Do not insert the power connector into the unit until the wiring is completed.
≥
Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all
cables and keep cable terminals free from touching any metal parts.
≥
Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
Caution
:
Clamp Connector
1
Example Combination
≥
Color LCD Monitor (CY-VM1500EX)
≥
External amplifier for subwoofer (CY-M7052)
≥
Center speaker (EAB-CF2)
≥
Subwoofer (CJ-SW46)
Basic system configuration
1
Power Connector
(for Power Amplifier Unit
)
;
No.
Item
When connecting an external amplifier through the pre-out connectors:
This unit's pre-out connectors have high-voltage specifications (5 Vrms). To ensure operation
with the best sound quality, it is recommended that the volume level be adjusted using the unit's
volume control while keeping the gain of the external amplifier at the medium.
