ー
82
ー
Operating Instructions
Intelligent Controller
72
Checking distribution data
Operation/Status
Checking distribution data in a list
Details about distribution data (distribution ratios, usage, and charges) are displayed in a list.
For indoor units used in tenanted buildings, it can be difficult
to know how much electricity or gas is used
in each area because the same air conditioning system may be used across multiple areas. By putting the indoor units in each area into “Distribution group”, rates can be calculated based on the data acquired from the air conditioning units (indoor units and outdoor units) in a “Distribution group”, and this can help you know how much electricity or gas is used in each area. The rate calculated by this is called the “Distribution ratio”.
You need to make the following settings before you can check distribution data.
y
Distribution mode settings (P
.160)
y
Area group name settings (P
.153)
y
Distribution group settings (P
.155)
y
Pulse meter settings (P
.158)
y
Calendar settings for distribution calculation (P
.148)
y
Distribution ratio settings (P
.161)
3
Set the period to be displayed.
z
Set the start and end of the period to be displayed.
z
The time at the left is the start of the period and the time at the right is the end.
(1) T
ouch
(3-1).
z
The “Calendar” dialogue is displayed showing the current date.
3-
1
(2) T
ouch the date (3-2).
z
Use
to select the month you want to check.
The
current month is displayed if you touch [ThsMth].
z
The settings are registered and the “Calendar” dialogue closes.
3-
2
Continued on next page
1
Touch [Accumulate/Distrib] in “Oper
./
Status”.
1
2
Touch [Distribution data].
z
The “Distribution data” screen is displayed.
2
73
Checking distribution data
Operation/Status
4
Set the time slots to display
.
(1) T
ouch [T
ime] (4-1).
z
The “Specify time” dialogue is displayed.
4-
1
(2)
Touch the time slot to accumulate (4-2).
z
Refer to “RglrHourRnge” in “Calendr sttgs for distr calc” (P
.148) for information about “Rglr hour1” to “Rglr hour8”.
z
The settings are registered and the “Specify time” dialogue closes.
4-
2
5
Checking distribution data.
Note
y
The calculations for distribution made by this unit do not acco
rd with the relevant laws and statutes, so they cannot be used
for official
transactions.
y
The operating time data accumulated on the indoor units is acquired via a communication adaptor
. When this unit sends a request for the
data to the communication adaptor
, the communication adaptor makes inquiries to the indoor units about their operating hours, and when
collection is complete is transfers the results to this unit.
This may result in a dif
ference in counts when moving from one time slot to the next.
y
Stopping of indoor units by scheduling is subject to some delays due to communications, so make sure it is not set at the same
time as the
“RglrHourRnge stngs” (P
.150) time slot is changed over
. If the schedule stops operation prior to the change over of a time slot, avoid setting it
inside 10
minutes (this may change depending on the state of communications) of the change over of the time slot.
y
When there is a problem with the communications between the main unit and the indoor units (or the communication adaptor), it m
ay not
be possible to accumulate by time slot normally
. The accumulated values received by this unit are counted in the time slot when they are
received.
y
The usage in [All hours] in the “Specify time” dialogue is calculated from the distribution ratio distributed overall according
to the total
operating data from all time slots.
This means that the usages in [RglHour], [OutOf hour], and [Sp
cfiedDay] will not match.
y
If you remove an air conditioning unit after accumulating distribution data, all accumulated values for that air conditioning u
nit are deleted, so
it will not be possible to view distribution data that includes that air conditioning unit after it is removed.
Before removing the unit, output (save) the distribution data a
s a CSV file to a USB memory device.
The output method for CSV files is the same as for outputting lo
gs. (→ “Outputting (saving) logs as a CSV file” (P
.60))
Checking distribution data in a list
TGR-318_ENG.indb 82
2017/04/06 10:43:22
