background image

2

(EN)

Safety Precautions

Read before installation

 

Read the Installation Instructions carefully 
to install the remote controller correctly and 
safely.
Be sure to read the Safety Precautions in 
particular before installation.

 

After the installation is complete, perform test 
operation to con

fi

 rm that no abnormality is 

present.

 

We assume no responsibility for accidents or 
damages resulting from methods other than 
those described in the installation instructions 
or methods without using speci

fi

 ed parts.

Malfunctions that occurred due to the 
unauthorised installation methods are not 
covered by the product warranty.

 

Read the installation instructions supplied with 
indoor units as well.

 WARNING

This symbol refers to a hazard or unsafe
practice which can result in severe personal 
injury or death.

 CAUTION

This symbol refers to a hazard or unsafe 
practice which can result in personal injury or 
product or property damage.

WARNING

•  Turn off the circuit breaker of the units before 

installation.

•  Ask your dealer or professionals for installation 

and electric work.

•  This controller shall be installed in accordance 

with National Wiring Regulations.

• Connect and 

fi

 x the speci

fi

 ed cables for wiring 

securely.

•  Do not allow the connection to be exposed to 

the external force of the cables.

•  Choose an installation location that suf

fi

 ciently 

supports the weight of the remote controller.

CAUTION

 

Do not use the remote controller at the 
following locations.

•  Location where condensation occurs
• Location where 

fl

 ammable gases, etc. may 

leak

•  Location where corrosive gases, etc. may leak
•  Location with lots of water or oil droplets 

(including machine oil)

•  Location where voltage 

fl

 uctuation frequently 

occurs

•  Location where there is a machine producing 

electromagnetic radiation

•  Location where droplets of organic solvents 

spread

•  Location where acidic or alkaline solutions or 

special sprays are frequently used

 

Do not operate with wet hands.

 

Do not wash with water.

NOTICE

The English text is the original instructions. Other languages are translation of the original 
instructions.

Summary of Contents for CZ-RWSU3











Reviews: