background image

ENGLISH

3

(EN)

Note:

 

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: (1) This 

device may not cause harmful interference, and (2) this 

device must accept any interference received, including 

interference that may cause undesired operation.

 

This equipment has been tested and found to comply with 

the limits for a Class B digital device, pursuant to Part 15 

of the FCC Rules. These limits are designed to provide 

reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, 

there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more 

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected.

• Consult the distributor or an experienced radio/TV 

technician for help.

 

FCC Caution: To assure continued compliance, follow 

the attached installation instructions.  Any changes 

or modi

fi

 cations not expressly approved by the party 

responsible for compliance could void the user’s authority 

to operate this equipment.

Summary of Contents for CZ-RWSU3

























Reviews: