- 15 -
ENGLISH
OPERA
TION
HOW TO USE ELECTRIC HOME SHOWER
1. HOW TO USE
Reco
mm
en
de
d T
em
p
ELB
Power Control
ELB Test
DH-3MP1
Push On-Off
ELB Reset
Push Up
Off
High
Power Control Knob
ELB
Power Control
ELB Test
DH-3MP1
Push On-Off
ELB Reset
Push Up
Off
High
Press
Shower Head
Shower Select
Button
(a)
(b)
(c)
Shower Hanger
Knob
Shower
Hanger
Make sure push
at the center of
Push On-Off
Lever only.
Reco
mm
en
de
d T
em
p
ELB
Power Control
ELB Test
DH-3MP1
Push On-Off
ELB Reset
Push Up
Off
High
Reco
mm
en
de
d T
em
p
ELB
Power Control
ELB Test
DH-3MP1
Push On-Off
ELB Reset
Push Up
Off
High
ELB: ON condition
ELB: OFF condition
6. Temperature setting
(a) The shower temperature can be gradually controlled by setting the Power Control Knob to the
desired position.
(b) If you turn the Power Control Knob clockwise the shower temperature will go up, reaching the
highest temperature at “High”. The temperature can be gradually controlled.
(c) If the Power Control Knob is at “Off” position, the water temperature will remain at inlet temperature.
(d) In case of continuous usage at high temperature setting, water temperature will increase and it may
cause the control device in the set to activate temporarily resulting water temperature to drop.
7. Select the preferred shower with the Shower Select Button. Please press the button fully.
8. Shower head can be set to various position.
(a) Loosen Shower Hanger Knob and adjust higher or lower.
Tighten Shower Hanger Knob.
(b) Loosen Shower Hanger Knob and Shower Hanger can be adjusted to the left or right.
Tighten Shower Hanger Knob.
(c) The angle of Shower Head can be adjusted by moving the Shower Head upper or lower.
1. Turn “On” the Main Water Valve.
2. Switch “On” the Miniature Circuit Breaker (MCB) and ON/OFF DP (double pole) Switch.
3. Push the ELB Reset Lever if it is down.
4. Turn Water Volume Knob to clockwise.
• Turning it clockwise increases the volume of water thus decrease the water temperature.
• Turning it anticlockwise decreases the volume of water thus increase the water temperature.
5. Press the Push On-Off Lever, water will start flowing from the Shower Head and the ELB light will turn red.
• To stop the water flow, press the Push On-Off Lever again (the position of the Push On-Off Lever
remains the same).
• This button controls both water and electricity supply to the set.
• Adjust to the desired shower condition by operating the Water Volume Knob and the Power
Control Knob.
Then the operation can be made easily by pushing the Push On-Off Lever only.
To ensure Pump reliability, Push On-Off Lever must be
pressed before and after each shower.
Do not pull the Push On-Off Lever, press only.
CAUTION
(1) How to adjust to maximum water flow rate.
Step 1:
Push the Push On-Off Lever and select Wide Shower type on the Shower Head using the Shower Select Button
(refer Figure 1).
Step 2:
Turn “Off” the Main Water Valve.
Step 3:
Turn the Shower Head upward at waist height.
Step 4:
Turn the Water Volume Knob to maximum volume position (refer Figure 2).
Step 5:
Gradually “On” the Main Water Valve and adjust the splashing height (H) of the shower.
It is recomended to adjust the water splashing height (H) at 100 cm ~ 110 cm (approximately 3 L/min).
(If splashing height (H) is too high, hot water temperature will drop because of an excessive flow rate).
2. WATER FLOW RATE ADJUSTMENT
Note: 1. Pay attention to shower temperature when reducing the volume of water.
The shower temperature will become very hot if the water flow rate is too low.
2. Water Volume Knob is at maximum position at this stage (refer Step 4).
Please adjust it to suitable flow rate using the Water Volume Knob by turning it anticlockwise.
Press
Spot Shower
Normal Shower
Wide Shower
Figure 1
Figure 2
Shower Select Button
H = 100 cm ~ 110 cm
Waist Height
Floor
Water Volume Knob
Main Water
Valve
Push On-Off Lever
ELB
Power Control
ELB Test
DH-3MP1
Push On-Off
ELB Reset
Push Up
Off
High
Water Volume Knob
CLEANING
FILTER
ELB Lamp
