22
Demonstration
lock/unlock
Ejection of the disc is prohibited.
The lock setting is effective until unlocking the
tray and not released by Main unit
initialization of service mode.
*When lock the tray.
“LOCK” is displayed for 3 seconds.
When the power is on, disc is in
tray, press and hold [OK], [B] and
[Y] on the remote control at the
same time for more than 5 seconds.
- "00 RET" is displayed on the unit's
disply.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "10 OCL" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
*When unlock the tray.
“UNLOCK” is displayed for 3 sec-
onds.
When the power is on, disc is in
tray, press and hold [OK], [B] and
[Y] on the remote control at the
same time for more than 5 seconds.
- "00 RET" is displayed on the unit's
disply.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "10 OCL" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
*When press [OPEN/CLOSE] key
while the tray being locked.
Display ”LOCK” for 3 seconds.
Press [OPEN/CLOSE] key while the
tray is being locked.
Progressive initialization The progressive setting is initialized to
Interlace.
When the power is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is dis-
played on the unit's disply.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit.
Default setting
The date of Menu, Mode and EEPROM
setting, etc. is set to the default condition in
factory.
“HELLO” is displayed 10 seconds.
While the unit is off, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "08 FIN" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit for at least 3 seconds.
Item
FL display
Key operation
Mode name
Description
Front Key
Summary of Contents for DMP-BDT110GC
