23
Demonstration
lock/unlock
Ejection of the disc is prohibited.
The lock setting is effective until unlocking the
tray and not released by Main unit
initialization of service mode.
*When lock the tray.
“LOCK” is displayed for 3 seconds.
When the power is on, disc is in
tray, press and hold [OK], [B] and
[Y] on the remote control at the
same time for more than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "10 OCL" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
*When unlock the tray.
“UNLOCK” is displayed for 3 sec-
onds.
When the power is on, disc is in
tray, press and hold [OK], [B] and
[Y] on the remote control at the
same time for more than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [STOP] on the
remote control until "10 OCL" is
displayed on the unit's display.
Press [OK] on the remote con-
trol or [OPEN/CLOSE] on the unit.
*When press [OPEN/CLOSE] key
while the tray being locked.
Display ”LOCK” for 3 seconds.
Press [OPEN/CLOSE] key while the
tray is being locked.
Progressive initialization The progressive setting is initialized to
Interlace.
When the power is on, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds. - "00 RET" is dis-
played on the unit's display.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "04 PRG" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit.
Default setting
The data of Menu, Mode and Nand-FLASH
setting, etc. is set to the default condition in
factory.
“HELLO” is displayed 10 seconds.
While the unit is off, press and
hold [OK], [B] and [Y] on the remote
control at the same time for more
than 5 seconds.
- "00 RET" is displayed on the unit's
display.
Repeatedly press
[
]
on the
remote control or [POWER] on the
unit until "08 FIN" is displayed on
the unit's display.
Press and hold [OK] on the
remote control or [OPEN/CLOSE]
on the unit for at least 3 seconds.
Item
FL display
Key operation
Mode name
Description
Summary of Contents for DMP-BDT220GA
