Helpful Hints
65
On the unit’s display
Page
On the TV
Page
On the unit’s display
Page
On the TV
Page
Error messages
∫
Common
H
, F
(“
” stands for a number.)
≥
An error has occurred. The number following “H” or “F” depends on the status of the
unit.
Reset procedure:
Press [POWER
Í
/I] to switch the unit to standby mode and then back to ON.
Alternatively, press [POWER
Í
/I] to switch the unit to standby mode, disconnect the
AC power supply cord, and then reconnect it.
≥
If the service numbers fail to clear, note the service numbers and contact a qualified
service person.
–
–
∫
DVD
Cannot finish recording completely.
≥
The program was copy-guarded.
≥
The disc may be full.
–
–
Cannot play.
≥
You inserted an incompatible disc (Discs recorded in PAL video, etc.).
–
Cannot record on the disc.
≥
The disc may be dirty or scratched.
19
Unable to format.
Please check the disc.
Cannot record. Disc is full.
≥
Create space by erasing any unwanted titles.
[RAM]
≥
Use a new disc.
[RAM]
[DVD-R]
23, 33, 37
–
Cannot record. Maximum number
of titles exceeded.
Error has occurred. Please press
ENTER.
≥
Press [ENTER] to start recovery process. You cannot operate the unit while it is
recovering (“SLF CHECK” appears on the unit’s display).
–
No disc.
≥
You haven’t inserted a disc. Correctly insert a disc that this unit can play.
≥
The disc is upside down. If it is a single-sided disc, insert it so the label is facing up.
18, 20
20
Please change the disc.
≥
There may be a problem with the disc. Press [
<
, OPEN/CLOSE] to remove it and
check it for scratches or dirt. (The unit turns off automatically after you open the tray.)
19
This is a non-recordable disc.
≥
The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized
DVD-R.
≥
You inserted an unformatted DVD-RAM. Format the disc with this unit.
–
31
This disc is not formatted properly.
≥
The operation is prohibited by the unit or disc.
21
CHK REMOTE
(“
” stands for a number.)
≥
The remote control and main unit are using different codes. Change the code on the
remote control or main unit.
17
HARD ERR
≥
If there is no change after turning the unit on and off, consult the dealer where the unit
was purchased.
–
NO READ
≥
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥
You have used a DVD-RAM/PD lens cleaner and it has finished. Press [
<
, OPEN/
CLOSE] to eject the disc.
19
19
PROG FULL
≥
There are already 16 timer programs. Delete unnecessary timer programs.
29, 53
SLF CHECK
≥
There was a power failure or the AC plug was disconnected while the unit was on. The
unit is carrying out its recovery process. Wait until the message disappears.
–
UNSUPPORT
≥
You have inserted a disc the unit cannot play or record on.
19
U14
≥
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling
fan on the rear of the unit.
–
U99
≥
The unit fails to operate properly. Press [POWER
Í
/I] on the main unit to switch the
unit to standby. Now press [POWER
Í
/I] again to turn the unit on.
–
∫
VHS
PLEASE PUT IN A VIDEO
CASSETTE.
≥
A video cassette is not inserted when recording programs or setting the timer
recording. Insert a video cassette with an intact erasure prevention tab.
48
PLEASE SET THE CLOCK
≥
The clock is not set when recording programs or setting the timer recording. Set the
clock.
46
PLEASE USE A CASSETTE WITH
TAB.
≥
A video cassette without the intact erasure prevention tab is inserted when recording
programs or setting the timer recording. Use a video cassette with an intact erasure
prevention tab.
48
VHS
DVD
PP-Sample.book 65 ページ ２００４年４月８日 木曜日 午後３時４５分
