29
Audio recording
1
Select the desired input signals using the
AUDIO IN switch.
To use the front microphone
i
Select FRONT (MIC).
To use the rear microphone
i
Select REAR (MIC).
To use the audio products
i
Select REAR (LINE).
AUDIO
SELECT
switch
AUDIO IN
switch
PHONES
jack
Rear mic power
switches
<Note>
≥
When the front microphone has been selected, select ON as the
<FRONT MIC POWER> setting for the MIC/AUDIO sub-menu
item if the phantom mic (+48 V) needs to be supported. (See page
36)
≥
Set the rear mic power switches to ON if the phantom mic (+48V)
must be supported when the external microphones are selected.
≥
When the wireless receiver is to be used, set the AUDIO IN
switch on the side panel to REAR (MIC or LINE), and select
WIRELESS as the REAR SEL CH1 and REAR SEL CH2 settings
for the <MIC/AUDIO> submenu item.
When the AUTO SELECT CH1/CH2 selector switch is set to AUTO,
the input levels of the CH1 and CH2 sound are automatically
adjusted.
To adjust the input levels of the CH1 and CH2 sound manually,
proceed as follows:
The audio input signals can be monitored through the monitor
speaker or earphone. When the PHONES jack is used, no sound
will be heard through the monitor speaker.
The volume of the monitored sound can be adjusted using the
MONITOR control.
<Note>
Howl may be caused if the volume of the audio monitor speaker is
too high. In a this situation, rotate the audio monitor level control to
a lower level which does not give rise to howl.
Monitoring the sound during
recording
Selecting the audio input signals
Adjusting the audio recording level
1
Set the AUTO SELECT CH1/CH2 selector
switch to MAN.
AUDIO LEVEL
CH1 control
Monitor
speaker
AUDIO LEVEL
CH2 control
2
While monitoring the audio level meter
displayed inside the viewfinder, adjust the
AUDIO LEVEL CH1 and CH2 knobs in such
way that the maximum input level will not
reach or exceed “- - - - - + - - - - +”.
POWER/
WARNING
AUDIO LEVEL
CH 1
RESET
MONITOR
MODE CHECK
AUTO IRIS MODE
QUICK FOCUS
FILTER
3200K
5600K
5600K
5600K
+1/8ND
+1/64ND
1
SCENE FILE
FULL
AUTO
BACK.L
SPOT.L
STD
COUNTER
TCG
TC
F-RUN
R-RUN
SET
UB
LITHIUM BATT
SEE MANUAL
CH 2
AUDIO SELECT
AUDIO
MIC
ON
OFF
FRONT
REAR
MIC
LINE
MAN
CH 1
CH 2
CH 1
CH 1
CH 2
CH 2
AUDIO IN
REAR MIC POWER
USER
F1
F2
F3
F4
STD
WHITE BAL
OUTPUT
GAIN
VTR
1
2
3
4
STBY
SA
VE
L
M
BA
SS
OFF
ON
AUTO
KN
EE
CA
M
H
PRST
A
B
JOG dial button
MONITOR control
EX TAPE NEAR END FLUO.
C
H
2
iREC TCG 12:34:56:00
0dB
1100 LOW LIGHT
DSep-01-01 23:59:00
=========
¢¢¢
min
13.
4V
Z78
ATW
F56
C
H
1
AWB+02
32K
.
.
SPOT QUICK FOCUS
¢
1
¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
¢
2
¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢
FL1
/
CH1
CH2
–32 –28 –24 –20 –16 –12 –8
–4 0dB
–40 –36
The reference value
<Notes>
≥
The level meter values shown in the figure on the right serve as a
rough guideline.
≥
When the unit is used in the MAN mode, the LIMITER CH1 and
LIMITER CH2 settings (see page 36) for the <MIC/AUDIO>
submenu item become operational.
