11.5. Electrical adjustment (LCD)
[How to enter into the LCD panel adjustment mode]
Play back the specified video signal (10 steps, color bas
signal).
Press and hold down "Back skip" and "Pause" of the main unit
at the same time while pressing "Menu" on the remote control
unit.
[The DVD player is now in the FT02 mode]
Press the "Forward skip button twice to enter into the FT04
mode (LCD panel adjustment mode).
Press the "Playback" button to play back the signal which has
been played back before stopping and then, press the "Pause
(still) button.
[How to exit to normal mode]
(Exit the F4 mode)
1. Turn off the primary power supply (Remove the DC power
supply).
Turn on the power supply. Press the "Stop" to stop the system.
Press "Cancel" on the remote control unit (The Cancel key is
enabled only when the system is stopped.)
l
Whenever the LCD panel is replaced, make the following
checks and adjustments.
l
Press the "Enter" key and fix the settings.
l
When the EEPROM" (IC3002) of the Main P.C.B. is replaced,
call up the LCD Panel adjustment mode (FT04) and execute
the AUDIO on the remove control unit and then check the
condition of the screen. Make adjustments as necessary.
11.5.1. Adjusting VCO oscillation
frequency
Adjustment is required when
Check point
The synchronization of the LCD
screen is irregular after any VCO-
related circuit part is replaced
TP8201
Adjustment procedure
Adjustment UP
Adjustment
DOWN
Use “1” on remote control unit.
DVD
player/remote
control unit
DVD
player/remote
control
Details of adjustment
Input video signal
Press “
“ and ”
”buttons on
remote controller, set the right
side number to “71”.
-----
11.5.2. Adjusting DC offset of impressed
voltage
Adjustment is required when
Check point
Noise such as horizontal stripes
is found on the screen.
TL8401
Adjustment procedure
Adjustment UP
Adjustment
DOWN
Use “3” on remote control unit.
DVD
player/remote
control unit
DVD
player/remote
control
Details of adjustment
Input video signal
Press “
“and”
”buttons on
remote controller, set the right
side number to “AI”.
10step monochrome
11.5.3. Adjusting white balance
red/subcontrast red
Adjustment is required when
Check point
Remarkable deviation in white
balance is found
TL8602
Adjustment procedure
Adjustment UP
Adjustment
DOWN
Use “6” on remote control unit.
DVD
player/remote
control unit
DVD
player/remote
control
Details of adjustment
Input video signal
(White balance)
Press “
“and “
“ buttons on
remote controller, set the number
of center to “80”.
(Sub contrast)
Press “
“ and “
“ buttons on
remote controller, set the right
side number to “7E”.
10step monochrome
11.5.4. Adjusting whitebalance
blue/subcontrast blue
Adjustment is required when
Check point
Remarkable deviation in white
balance is found
TL8604
Adjustment procedure
Adjustment UP
Adjustment
DOWN
Use “7” on remote control unit.
DVD
player/remote
control unit
DVD
player/remote
control
Details of adjustment
Input video signal
(White balance)
Press “
“and “
“ buttons on
remote controller, set the number
of center to “71”.
(Sub contrast)
Press “
“and “
“ buttons on
remote controller, set the right
side number to “84”.
10step monochrome
35
DVD-LX110EE / DVD-LX110GCS
Summary of Contents for DVD-LX110EE
