Panasonic EASA-PHONE KX-T123210 Installation Manual Download

Page: 213 / 242

LIMITED WARRANTY

Panasonic Company, PHI or PSC will repair this product with new or rebuilt parts, free of

charge, in the U.S.A. or Puerto Rico for one ( 1 ) year from the date of original purchase in the

event of a defect in materials or workmanship.

Batteries

( if included )

New rechargeable batteries in exchange for defective rechargeable

batteries for ten (10) days from the date of original purchase. Non-rechargeable batteries are

not warranted.

Carry-in or mail-in service in the continental U.S.A. can be obtained during the warranty

period from a Matsushita Services Company (MSC ) Factory Servicenter listed in the Servicenter

Directory. Or call l-800-447-4700, toll free, to locate an authorized MSC Servicenter. Carry-in or

mail-in service in Puerto Rico or Hawaii can be obtained during the warranty period by calling

the telephone numbers listed in the Servicenter Directory (see page 6-11 ) .

This warranty is extended only to the original purchaser. A purchase receipt or other proof of

date of original purchase will be required before warranty performance is rendered.

This warranty only covers failures due to defects in materials or workmanship which occur

during normal use. It does not cover damage which occurs in shipment or failures which are

caused by products not supplied by Panasonic Company, PHI or PSC or failures which result

from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty

installation, modification, or service by anyone other than a MSC Factory Servicenter or

authorized MSC Servicenter or damage that is attributable to acts of God.

LIMITS AND EXCLUSIONS

There are no express warranties except as listed above.

PANASONIC COMPANY, PHI AND PSC SHALL NOT BE LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE

PRODUCT, OR

OUT OF ANY BREACH OF THIS WARRANTY.

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE

APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some

not allow the exclusion

or limitation of incidental or consequential damages, or limitations on how long an implied

warranty lasts, so the above exclusions or limitations may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary

from state to state.

If a problem with this product develops during the warranty period, you may contact your

dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the

Consumer Affairs Division at the company address indicated on the back cover.

6-10

Summary of Contents for EASA-PHONE KX-T123210



















































































































































































































































Search results

Summary of Contents for EASA-PHONE KX-T123210

Reviews:

Related manuals for EASA-PHONE KX-T123210

Brands by name

Popular brands

Panasonic EASA-PHONE KX-T123210, Installation Manual

Search results

Summary of Contents for EASA-PHONE KX-T123210

Reviews:

Related manuals for EASA-PHONE KX-T123210

Brands by name

Popular brands