background image

ENGLISH - 3

Read this first!

WARNING:

Installation work should only be carried out by the certified personnel.

 

z

If this product is not installed correctly, serious accidents may result.

 

z

Follow the instructions specified in “Installation” of this manual, and perform secure installation.

Install the ceiling mount bracket in accordance with the structure and materials of the installation 

location.

 

z

If a mistake is made in the installation procedure, the ceiling mount bracket may fall down and an injury may 

result.

Mounting must be carried out by two or more persons.

 

z

When installing the projector in an overhead location, for example, in a high ceiling, at least two persons will 

be required to handle the installation.

Make sure that your footing is safe and secure during installation.

 

z

If your footing is not secure, you may trip or fall down, and an injury may result.

Do not loosen or remove the unit screws and bolts unnecessarily.

 

z

The projector may fall down and an injury may result.

Do not install in a location that is not strong enough.

 

z

If the installation location is not strong enough, the unit may fall down and damage to the projector or an 

injury may result.

Do not install the ceiling mount bracket in humid or dusty locations or in locations where the ceiling 

mount bracket may be exposed to oily smoke, steam, or excessive heat.

 

z

Failure to obey may result in fire or electric shock. In addition, oil will cause the plastic to deteriorate, which 

may result in a drop hazard.

Do not allow children to reach the supplied screws and metal fittings.

 

z

These items can cause personal injury if swallowed.

 

z

If swallowed, seek medical help immediately.

Do not disassemble or modify the projector mount bracket.

 

z

The projector may be damaged or fall down, and an injury may result.

CAUTION:

Install only the designated projector.

Install only using the designated method.

 

z

Failure to obey may result in dropping, damage to the projector, or injury.

Do not install the ceiling mount bracket in a place which may impede projector ventilation.

 

z

If this is not observed, fire may result.

Do not hang from or hang objects on the projector or ceiling mount bracket.

 

z

The projector may fall and cause injury.

Use only the specified ceiling mount bracket (for high ceilings or for low ceilings).

 

z

Failure to obey may result in dropping, damage to the projector, or injury.

Always use the supplied parts when performing installation.

 

z

Otherwise, this may cause damaged projector to fall and cause injury.

Install the mounting screws and power cable in such a way that they will not make contact with the 

inside metals of the ceiling.

 

z

Electric shocks may result from contact with any metal objects inside the ceiling.

 

Panasonic disclaims all liability for any accidents or any damage caused by the installation of the 

ceiling mount bracket using methods that are not described in these Installation Instructions or 

methods that do not use the parts specified in these Instructions.

 

■ If products are no longer being used, they should be dismantled and removed by the certified 

personnel as soon as possible.

Always follow these precautions

ET-PKD130B_EN_TQZJ577-7.indd   3

2017/03/13   19:04:50

Summary of Contents for ET-PKD130B



















Reviews: