4 - ENGLISH
Product components
This is a projector mount bracket for installing projectors.
Use this together with the ceiling mount bracket for high ceilings or low ceilings (sold separately).
■
Supported ceiling mount brackets and projectors
z
Ceiling Mount Bracket
ET-PKD130H / ET-PKD120H / ET-PKD120S / ET-PKD310H / ET-PKD310S / ET-PKD56H / ET-PKD55S /
ET-PKD100H / ET-PKD100S / ET-PKD77H / ET-PKD75S
z
Projector
PT-RZ575 / PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 / PT-RZ970 / PT-RW930 / PT-RX110 / PT-DZ780 /
PT-RZ570 / PT-DW750 / PT-DX820 / PT-RZ670 / PT-RW630 / PT-DZ870 / PT-DW830 / PT-DX100 / PT-DZ770 /
PT-DZ680 / PT-DZ6710 / PT-DZ6700 / PT-DW740 / PT-DW730 / PT-DW640 / PT-DW6300 / PT-DX810 /
PT-DX800 / PT-DX610 / PT-D6000 / PT-D5000
Note
z
Installation of the ET-PKD130H ceiling mount bracket (for high ceilings, 6-axis adjustment) is recommended if
the projector will be used with the optional ET-DLE030 Fixed-focus lens. When installed using the
ET-PKD130H you can more accurately adjust horizontal tilt of the projector.
z
Products not listed above may be supported in some cases. For details, refer to the operating instructions of
your ceiling mount bracket (for high ceilings or for low ceilings) and projector.
z
In this document, the letters at the end of the projector part numbers are omitted.
■
Structural components
Check that the package contains the following parts. The number enclosed in < > is the quantity.
Projector mount bracket < 1 >
This is used to install the projector itself.
The bracket has a function for adjusting horizontal tilt.
Hex head bolt,
captive washer < 6 >
(M6×16)
These are used to mount the bracket onto the projector.
Flat washer < 2 >
(M8)
Prevents the projector from falling.
Wire rope < 1 >
(Approx. 2.5 mm (3/32")
wire diameter,
800 mm (31-1/2") length)
z
Tightening torque for the screws are
M6: 4±0.5 N•m, M8: 10±1 N•m
.
z
When tightening up the screws, use a tool such as a torque screwdriver or torque wrench. Do not use electric
screwdrivers or impact screwdrivers.
Note
z
The projector models listed below require five of the six supplied captive washer hex head bolts (M6 × 16) for
installation.
Model: PT-RZ575 / PT-RZ770 / PT-RW730 / PT-RZ660 / PT-RW620 / PT-RZ970 / PT-RW930 / PT-RX110 /
PT-DZ780 / PT-RZ570 / PT-DW750 / PT-DX820 / PT-RZ670 / PT-RW630 / PT-DZ770 / PT-DZ680 /
PT-DZ6710 / PT-DZ6700 / PT-DW740 / PT-DW730 / PT-DW640 / PT-DW6300 / PT-DX810 / PT-DX800 /
PT-DX610 / PT-D6000 / PT-D5000
ET-PKD130B_EN_TQZJ577-7.indd 4
2017/03/13 19:04:51
