background image

ENGLISH - 5

Read this first!

IMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse 

is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating 

of 13 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark   or the BSI mark   on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you 

lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover 

can be purchased from an Authorised Service Center.

If the fitted moulded plug is unsuitable for the mains socket in your home, then the fuse should be 

removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the 

cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below.

If in any doubt, please consult a qualified electrician.

WARNING:

THIS APPLIANCE MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Green - and - Yellow:  Earth

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings 

identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the 

plug which is marked with the letter E or by the Earth symbol   or coloured GREEN or GREEN - 

AND - YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked 

with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked 

with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

13A250V

BS

13

63

/A

HE-8

N

ASA

L

Importer’s name and address within the European Union
Panasonic Marketing Europe GmbH
Panasonic Testing Center
Winsbergring 15, 22525 Hamburg, Germany

Summary of Contents for ET-RPS100G













Reviews: