Panasonic EY7880 - 28.8V ROTARY HAMMER Service Manual Download | Manualshive

Page: 11 / 17

background image

11

Ref. No. 2B

Procedure 2A

→

2B

Assembly of gear case assembly.

1. Assemble the chuck spring and the chuck spring plate.
2. Insert a ball pushing down the chuck spring.
3. Inject an adhesive such as Cemedine SX720WH and wipe off to
bury the gap between the gear case A and B in order to prevent the
leakage of grease inside of gear box.

NOTE:

Make sure an adhesive is completely dried before assembling
the driving block into the houshing.

«
...
9
10
11
12
13
...
»

Summary of Contents for EY7880 - 28.8V ROTARY HAMMER


















Reviews:

No comments

Related manuals for EY7880 - 28.8V ROTARY HAMMER

Brand: Daewoo Pages: 24

Brand: Hitachi Pages: 78

Brand: Hitachi Pages: 76

Brand: Hitachi Pages: 44

Brand: Worx Pages: 84

Brand: KRESS Pages: 16

Brand: KRESS Pages: 52

Brand: Sparky Group Pages: 110

Brand: Far Tools Pages: 42

Brand: Makita Pages: 72

Brand: Makita Pages: 64

Brand: Makita Pages: 36

Brand: KRAUSMANN Pages: 20

Brand: Ironton Pages: 13

Brand: Stanley Pages: 18

Brand: Stanley Pages: 21

FATMAX SFMEH200

Brand: Stanley Pages: 76

Brand: BorMann Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands