background image

GENERAL SAFETY INFORMATION

PLEASE READ PRIOR TO INSTALLING THIS FAN

DESCRIPTION

UNPACKING

SUPPLIED ACCESSORIES

DIMENSIONS

WIRING DIAGRAM

FEATURE

INDICATION (PLUG ‘N PLAY FUNCTION DEVICES)

MOTION (PLUG ‘N PLAY FUNCTION DEVICES)

INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES)

INSTALLATION (NEW CONSTRUCTION)

INSTALLATION (RETROFIT)

MAINTENANCE     (CLEANING)

SPECIFICATIONS

PRODUCT SERVICE

FV -0511V K 2     FV -0511V KS 2

FV -1115V K 2

INSTALLATION INSTRUCTIONS

Ventilating Fan

Model  No.

Contents

FV-0511VKS2

FV-0511VK2
FV-1115VK2

Representative models:

2-3
3-4

4
4
4
5
5

 5

6-7

7
8

8-10

10
11

BACK COVER

BACK COVER

PRACTICAL GUIDE TO INSTALLATION

BACK COVER

READ AND SAVE THESE INSTRUCTIONS 

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting to install, operate or service

the Panasonic product. Please carefully read the “GENERAL SAFETY INFORMATION” 

Failure to comply with instructions could result in personal injury or property damage. 

Please explain to users how to operate and maintain the product after installation, 

and this booklet should be presented to users.

Please retain this booklet for future reference.

Summary of Contents for FV-0511VK2













Reviews: