Panasonic FV-11VF2 Installation Instructions Manual Download

Page: 6 / 12

Fig.2-2

Fig.2-1

(Fig.3)

Fig.2-3

Illustrations in this manual common use the image of
FV-11VHL2, and mark for FV-11VHL2 only, others are
same for FV-11VH2.

INSTALLATION (JOIST MOUNTING- )

Fig.3

Fan body

Suspension
bracket

Fan body

Suspension
bracket

Fan body

Joist

4 Long screws (ST4.2X20)

2 Screw (ST4.2X8)

Suspension bracket

2. Insert the suspension bracket into the fan body.
(Select the suspension bracket as shown below.)

Fig.1

Tape

Fan body

Warning label

Fig.4-2

Joist

2 Long screws
(ST4.2X20)

Screw
(ST4.2X12)

Joists

16 inches and 19.2 inches
horizontal joists

Fig.4-1

16 inches and 19.2 inches
horizontal joists refer to Fig.4-1, 19.2 inches vertical
joists and 24 inches refer to Fig.4-2.

Joist

2 Long screws
(ST4.2X20)

Screw
(ST4.2X12)

1. Before installation, remove warning lable and the tape
that is securing the adapter and the damper. (Fig.1)

Summary of Contents for FV-11VF2













Search results

Summary of Contents for FV-11VF2

Reviews:

Related manuals for FV-11VF2

Brands by name

Popular brands

Panasonic FV-11VF2, Installation Instructions Manual

Search results

Summary of Contents for FV-11VF2

Reviews:

Related manuals for FV-11VF2

Brands by name

Popular brands