background image

8

http://panasonic-electric-works.net/sunx

Overseas Sales Division (Head Office) 

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan 

Phone: +81-568-33-7861  FAX: +81-568-33-8591

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany

Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue, New Providence, New Jersey 07974, USA

Phone: +1-908-464-3550

16

sPEcIFIcatIons

Item

standard

long sensing range

FX-101-Z (NPN output)

FX-102-Z (NPN output)

FX-101P-Z (PNP output)

FX-102-PZ (PNP output)

Supply voltage

12 to 24V DC±10% Ripple P-P 10% or less (within the rated range)

Power consumption

Normal operation: 720mW or less 
(Current consumption 30mA or less at 24V supply voltage)
ECO mode: 600mW or less 
(Current consumption 25mA or less at 24V supply voltage)

output

NPN output type

NPN open-collector transistor

 

Maximum sink current: 100mA

 

Applied voltage: 30V DC or less (between output and 0V)

 

Residual voltage: 1.5V or less (at 100mA sink current)

PNP output type

PNP open-collector transistor

 

Maximum source current: 100mA

 

Applied voltage: 30V DC or less (between output and +V)

 

Residual voltage: 1.5V or less (at 100mA source current)

output operation

Light-ON or Dark-ON, selectable

short-circuit protection

Incorporated

External input

NPN output type

NPN non-contact input

 

Signal condition: 
High: +8V to +V DC or Open  
Low: 0 to +2V DC (Source current 0.5mA or less)

 

Input impedance: Approx. 10k

W

PNP output type

PNP non-contact input

 

Signal condition  
High: +4V to +V DC(Sink current 0.5 to 3mA or less)  
Low: 0 to +0.6V DC or Open 

 

Input impedance: Approx. 10k

W

response time

 

Emission frequency 0:250

m

s or less

 

Emission frequency 1: 450

m

s or less

 

Emission frequency 2: 500

m

s or less

 

Emission frequency 3: 600

m

s or less

 

Emission frequency 1: 2.5ms or less

 

Emission frequency 2: 2.8ms or less

 

Emission frequency 3: 3.2ms or less

 

Emission frequency 4: 5.0ms or less

Ambient temperature

-10 to +55˚C (No dew condensation or icing allowed, see note)

Storage: -20 to +70˚C

Ambient humidity

35 to 85% RH, Storage: 35 to 85% RH

Emitting element

Red LED (peak wavelength = 632nm)

Material

Enclosure: Polycarbonate, Fiber lock lever: PBT

Weight

Approx. 15g (Main body only)

When using the products in parallel, the ambient temperature is as follows: 4 to 7 units: -10 to +50˚C, 8 to 16 units: -10 to +45˚C

Summary of Contents for FX-100-Z Series









Reviews: