background image

  

CONTENTS

 

SAFETY PRECAUTIONS 

GENERAL INFORMATION 

WARNING 

CAUTIONS

 

2

 

 

 

 

MODULE SPECIFICATIONS

 

MECHANICAL LOADING

 

 

STANDARDS 

FIRE CLASS OF PRODUCT 

BYPASS DIODE

 

5

 

INSTALLATION 

GENERAL 

OPERATING CONDITIONS 

SPECIAL CONDITIONS 

UNPACKING AND HANDLING 

MODULE INSTALLATION

 

 

WIRING 

GENERAL 

MODULE WIRING 

ARRAY WIRING 

EARTH GROUND WIRING 

GROUNDING METHODS

 

 

 

 

 

MAINTENANCE 

ANTI-REFLECTION GLASS SURFACE 

CLEANING

 

 

13 

 

 

DISCLAIMER OF LIABILITY 

CONTACT INFORMATION 

13 

13

 

“HIT” is a trademark of the Panasonic Group. 

Other product and service names listed in this 

manual are trademarks or registered trademarks 

of respective companies.

 

 

General Installation Manual

 

VBHNxxxSA series 

VBHNxxxKA series 

Photovoltaic Module HIT

®

 

Thank you for choosing Panasonic photovoltaic module HIT

®

Please read this manual completely before you install or use of 

HIT

®

. With proper operation and maintenance, HIT

®

 will pro-

vide you with clean, renewable solar electricity for many years. 

This manual contains important installation, maintenance and 

safety information. The word “module” as used in this manual 

refers to one or more PV modules.  Retain this manual for 

future reference.   

 

Model No. 

VBHNxxxSA17 

    xxx=330, 325 

VBHNxxxKA03 

    xxx=325, 320

 

VBHNxxxSA17 series 

VBHNxxxKA03 series 

Summary of Contents for HIT VBHN320KA03















Reviews: