The NDSS Monitor Release feature is used to stop monitoring a certain extension. When this feature is
performed at a monitor PBX:
•
If no other PBXs are monitoring the selected extension, the monitored PBX stops transmitting status
information for that extension.
•
The monitor PBX stops receiving status information for the selected extension. All NDSS buttons for
that extension stop displaying status information.
However, the related information is not deleted from the Network Monitor Extensions Table. Therefore, if
an extension user at a monitor PBX subsequently goes off-hook and presses the NDSS button for that
extension, monitoring will be reactivated. To completely remove monitoring of an extension, the registration
data must also be deleted from the Network Monitor Extensions Table at each monitor PBX.
The monitor destination of each NDSS button is determined by the registration information for a particular
index number in this table. Therefore, if the registration information for an index number is changed (for
example, the Network Extension Number assigned to Index No. 001 in the example above is changed from
"2001" to "4002"), any NDSS buttons that have been set for that extension will automatically point to the
new monitor destination.
Conditions
•
Hardware Requirements:
The PLMPR/PMPR/PSMPR Software File Version of all PBXs in the network must be 2.0xxx or later.
The KX-TDA6920, KX-TDA0920, or KX-TDA3920 SD Memory Card for Software Upgrade to Enhanced
Version must be installed in all PBXs that will monitor extensions or have extensions monitored. (PBXs
with Network ID 0 can use the standard KX-TDA0820 or KX-TDA3820 SD Memory Card for Software
Upgrade.)
If using an IP-GW4E card (KX-TDA0484), the firmware (not LPR) of the card must be version 1.2 or later.
If using a PRI23 card (KX-TDA0290), the LPR software of the card must be version 1.009 or later.
•
All PBXs in the network must be KX-TDA series, KX-TDE series, or KX-NCP series PBXs. For information
on the hardware requirements for KX-TDE/KX-NCP series PBXs that will monitor extensions or have
extensions monitored, refer to the corresponding Feature Guide.
•
Each of Network PBX IDs 1-8 can only be assigned to one PBX within a network. Assigning the same
Network PBX ID to two PBXs will cause network data transmission problems.
•
It is only possible to assign NDSS buttons for extensions that have been previously registered in the
Network Monitor Extensions Table.
6.5 [4-1-4] Wired Extension—Flexible Button
®
®
6.13 [4-2-3] Portable Station—Flexible Button
®
®
®
®
•
Extensions connected to one PBX can monitor a maximum of 250 extensions at other PBXs. One extension
can be monitored by multiple extensions at multiple PBXs.
•
To reduce NDSS data traffic, it is recommended that 8 or less extensions in a single Incoming Call
Distribution Group be monitored.
•
Activation of an NDSS button is only required the first time that a button for a newly registered extension
is created. Once an NDSS button has been activated by being pressed the first time, any further NDSS
buttons for the same monitored extension will automatically display the extension status without needing
to be activated.
•
To use the NDSS Monitor Release feature, an extension must be assigned as a manager.
®
4.11 [2-7-1] Class of Service—COS Settings—Programming & Manager—
®
366
Feature Guide
1.30.5 QSIG Enhanced Features
Summary of Contents for HYBRID IP-PBX KX-TDA200
