32
4.4.3
IMAGE
From Main Menu->SETTING->REMOTE->IMAGE, you can see the camera interface is shown as
below. See Figure 4-13.
Channel: Select a channel from the dropdown list.
Configuration:
Here you can set up 4 modes of configurations for Day/Night switch:
Day/Night/Normal/Switch By Period.
Day:
Day mode.
Night: Night mode.
Normal: Normal mode.
Switch By Period: Switch Day/Night mode due to the time.
Saturation: It is to adjust monitor window saturation. The value ranges from 0 to 100. The default
value is 50. The larger the number, the stronger the color is. This value has no effect on the general
brightness of the whole video. The video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white balance is not accurate. Please note
the video may not be attractive if the value is too low. The recommended value ranges from 40 to 60.
Brightness: It is to adjust monitor window bright. The value ranges from 0 to 100. The default value is
50. The larger the number is, the brighter the video is. When you input the value here, the bright
section and the dark section of the video will be adjusted accordingly. You can use this function
when the whole video is too dark or too bright. Please note the video may become hazy if the value
is too high. The recommended value ranges from 40 to 60.
Contrast: It is to adjust monitor window contrast. The value ranges from 0 to 100. The default value
is 50. The larger the number is, the higher the contrast is. You can use this function when the whole
video bright is OK but the contrast is not proper. Please note the video may become hazy if the value
is too low. If this value is too high, the dark section may lack brightness while the bright section may
over exposure .The recommended value ranges from 40 to 60.
Sharpness: The value here is to adjust the edge of the video. The value ranges from 0 to 100. The
larger the value is, the clear the edge is and vice versa. Please note there is noise if the value here is
too high. The default value is 50 and the recommended value ranges from 40 to 60.
Mirror: It is to switch video up and bottom limit. This function is disabled by default.
Flip: Here you can set up for image rotation.
No Flip: No image rotation.
Flip 180
°
: Image rotates by 180°
Clockwise90
°
: Image clockwise rotates by 90°
Counter Clockwise90
°
: Image counter clockwise rotates by 90°
3D Denoise: 3D noise reduction
BLC: It includes several options: BLC/WDR/HLC/OFF.
BLC: The device auto exposures according to the environments situation so that the darkest area of
the video is cleared
WDR: For the WDR scene, this function can lower the high bright section and enhance the
brightness of the low bright section. So that you can view these two sections clearly at the same time.
The value ranges from 1 to 100. When you switch the camera from no-WDR mode to the WDR mode,
system may lose several seconds record video.
HLC: After you enabled HLC function, the device can lower the brightness of the brightest section
according to the HLC control level. It can reduce the area of the halo and lower the brightness of the
whole video.
Summary of Contents for k-nl308k
