background image

Roller Cleaning Paper

Using a pair of scissors, open the bag along the dotted

line (

A

), and take out the roller cleaning paper.

If the bag is left opened for a long period of time before

using it, the alcohol will evaporate. Please use the roller

cleaning paper immediately after opening the bag.

1

Notice

Keep the roller cleaning paper out of reach of

small children.

Do not store the roller cleaning paper in direct

sunlight or in a place with a temperature over

40 °C (104 °F).

Only use the roller cleaning paper to clean the

rollers.

For details about the roller cleaning paper, refer

to the Material Safety Data Sheet (MSDS).

Please ask your Panasonic sales company

about obtaining the Material Safety Data Sheet.

To purchase the roller cleaning paper

(KV-SS03), please contact your dealer, or call

our Supplies and Accessories department at

1-800-726-2797 (U.S.A. only).

KEEP AWAY FROM FIRE.

Security Notice

The management of documents and scanned data is

the responsibility of the user. In particular, pay attention

to the following points.

Make sure you have the same number of pages for

important documents both before and after

scanning, and take care not to leave any pages in

the scanner.

Periodically back up important data.

When having your computer or hard disk serviced,

or when disposing of your computer or hard disk,

completely erase any stored image data.

Others

Make sure to remove paper clips and staples from

documents before scanning. Failing to do so can

damage the unit, document, or both.

Do not use thinner, benzine, or cleaners containing

abrasives or surfactants, for cleaning the outside of

scanner.

10

Operating Manual

Before You Start

Summary of Contents for KV-S1027C












































































Reviews: