Remote Operation
78
Other remote operations
Erasing a specific message
Press
{
{
{
{*
*
*
*}{
}{
}{
}{
4
}
}
}
}
while listening to the message
you want to erase.
Voice guide example:
“The message has been erased.”
L
A long beep will sound. The unit will then play
back the next message.
Erasing all the messages
Press
{
{
{
{*
*
*
*}{
}{
}{
}{
5
}
}
}
}
to erase all the messages.
Voice guide example:
“All messages have been erased.”
L
A long beep will sound.
Monitoring the room
Press
{
{
{
{
6
}
}
}
}
to monitor the sound for about 30
seconds in the room where the unit is installed.
L
After 30 seconds, a beep will sound. To
continue monitoring, press
{
{
{
{
6
}
}
}
}
again within
10 seconds.
Recording a marker message
After playing back the recorded messages, you
can leave an additional message.
1.
Wait for the voice guide.
Voice guide example:
“All messages have been played.”
2.
Wait about 10 seconds.
Voice guide example:
“Please leave your name and message after
the beep.”
3.
Leave a message after the beep.
Re-recording a greeting message
You can change the contents of the TAD/FAX
greeting message.
1.
Press
{
{
{
{
7
}
}
}
}
to start recording.
L
A long beep will sound.
2.
Speak clearly up to 16 seconds.
L
If you pause for over 2 seconds, 6 beeps
will sound and the recording will stop.
Repeat from step 1 within 10 seconds.
3.
When finished recording, press
{
{
{
{
9
}
}
}
}
.
L
The new greeting message will be played.
Skipping the greeting message
Press
{
{
{
{
0
}
}
}
}
during the greeting message
playback.
L
The unit will skip the rest of the greeting
message.
Turning the message transfer on or off
You must program a transfer telephone number
beforehand (feature #60, page 91).
Press
{
{
{
{
8
}{
}{
}{
}{
1
}
}
}
}
to turn on the message transfer.
Voice guide example:
“Message transfer is set. Transfer phone
number is 123...”
Press
{
{
{
{
8
}{
}{
}{
}{
2
}
}
}
}
to turn off the message transfer.
Voice guide example:
“Message transfer is off.”
L
If a transfer telephone number is not
programmed, you cannot turn this feature on.
Voice guide example:
“Transfer phone number is not set.”
Turning the pager call on or off
You must program a pager number beforehand
(feature #70, page 91).
Press
{
{
{
{
8
}{
}{
}{
}{
3
}
}
}
}
to turn on the pager call.
Voice guide example:
“Pager call is set. Pager number is 098765432.”
Press
{
{
{
{
8
}{
}{
}{
}{
4
}
}
}
}
to turn off the pager call.
Voice guide example:
“Pager call is off.”
L
If a pager number is not programmed, you
cannot turn this feature on.
Voice guide example:
“Pager number is not set.”
Changing the receive mode
Press
{
{
{
{
8
}{
}{
}{
}{
0
}
}
}
}
to change the receive mode from
TAD/FAX to TEL.
L
You cannot return to TAD/FAX mode in the
same call. To return to TAD/FAX mode, see
the following.
Setting to TAD/FAX mode from TEL mode
1.
Call your unit and wait for 10 rings.
L
The answering device will temporarily
answer the call.
2.
Enter the remote operation ID during the
greeting message.
L
A long beep will sound, and your unit will
switch to TAD/FAX mode.
3.
Hang up the handset.
