8. Programmable Features
35
Code #49:
S
ettin
g
the auto disconnection
AUTO DISCONNECT
=ON
[
±
]
To answer a call with an extension telephone in TEL/FAX
mode (page 25), activate this feature and program the
code.
1.
Press
{
MENU
}
.
2.
Press
{#}
, then
{
4
}{
9
}
.
3.
Press
{A}
or
{B}
repeatedly to select
“
ON
”
.
4.
Press
{
S
ET
}
.
5.
Enter your code from 2 to 4 digits, using 0-9 and
{*}
.
L
The default code is
“
;
0
”
6.
Press
{
S
ET
}
.
7.
Press
{
MENU
}
.
Code #54: Chan
g
in
g
the recordin
g
time for your
TAM/FAX
g
reetin
g
messa
g
e (KX-FT9
88
only)
GREETING TIME
=16s
[
±
]
“
16s
”
(default): Maximum recording time is 16 seconds.
“
60s
”
: Maximum recording time is 60 seconds.
See page 29 for details.
Code #5
8
:
S
ettin
g
the scan contrast
SCAN CONTRAST
=NORMAL
[
±
]
To send or copy a document with faint or dark writing, set
this feature before starting transmission or copying.
“
NORMAL
”
(default): Used for normal writing.
“
LIGHT
”
: Used for dark writing.
“
DARKER
”
: Used for faint writing.
L
This feature is not valid if you select
“
PHOTO
”
resolution for sending (page 20) or copying (page 2
8
)
a document.
Code #59:
S
ettin
g
the print contrast
PRINT CONTRAST
=NORMAL
[
±
]
To adjust the darkness of received or copied documents.
“
NORMAL
”
(default): Normal contrast.
“
DARKER
”
: Darker contrast.
Code #67:
S
ettin
g
the incomin
g
messa
g
e monitor
(KX-FT9
88
only)
ICM MONITOR
=ON
[
±
]
To hear an incoming message (ICM) from the speaker
when the answering device is recording the message.
“
ON
”
(default): You can monitor the incoming message.
“
OFF
”
: Deactivates this feature.
Code #72:
S
ettin
g
recall/flash time
SET FLASH TIME
=600ms
[
±
]
The recall/flash time depends on your telephone
exchange or host PBX. You can select
“
900ms
”
,
“
700ms
”
,
“
600ms
”
(default),
“
400ms
”
,
“
300ms
”
,
“
250ms
”
,
“
200ms
”
,
“
160ms
”
,
“
110ms
”
,
“
100ms
”
,
“
90ms
”
or
“
80ms
”
.
Note:
L
If the unit is connected via a PBX, this setting may
need to be changed in order for PBX functions
(transferring a call, etc.) to work correctly. Consult
your PBX supplier for the correct setting.
L
If you set the location setting to
“
CZECH
”
or
“
SLOVAKIA
”
(feature #74 on page 35), the default
setting will be
“
100ms
”
.
Code #73: Chan
g
in
g
the receivin
g
mode in the
manual answer settin
g
MANUAL ANSWER
=TEL
[
±
]
“
TEL
”
(default): Telephone mode (page 24)
“
TEL/FAX
”
: Telephone/Fax mode (page 25)
Code #74:
S
ettin
g
the location where you use this
unit
LOCATION
=EAST EUROPE [
±
]
This setting must match your location.
“
EAST EUROPE
”
(default): To use in East Europe
countries.
“
CZECH
”
: To use in Czech Republic.
“
SLOVAKIA
”
: To use in Slovakia.
Code #76:
S
ettin
g
the connectin
g
tone
CONNECTING TONE
=ON
[
±
]
If you often have trouble when sending faxes, this feature
allows you to hear connecting tones: fax tone, ring back
tone and busy tone. You can use these tones to confirm
the status of the other party’s machine.
“
ON
”
(default): You will hear connecting tones.
“
OFF
”
: Deactivates this feature.
Note:
L
If the ring back tone continues, the other party’s
machine may not be a fax machine or may have run
out of paper. Check with the other party.
L
The connecting tone volume cannot be adjusted.
Code #77: Chan
g
in
g
the receivin
g
mode in the auto
answer settin
g
(KX-FT9
88
only)
AUTO ANSWER
=TAM/FAX
[
±
]
“
TAM/FAX
”
(default): Telephone Answering
Machine/Fax mode (page 25)
