DISA Security Mode and Available Features
If the DISA AA service is not employed, the caller may access the PBX features by entering the feature
numbers. To prevent others from accessing the PBX features, it is possible to assign DISA security.
→
7.3 [5-3-1] Voice Message—DISA System—
DISA Security—DISA Security Mode
→
The features available depend on the preprogrammed DISA security mode as follows:
Security Mode
Intercom
Call
TIE Line Call
Trunk Call
Without PBX Code
With PBX Code
All Security
Trunk Security
ü
ü
No Security
ü
ü
ü
ü
ü
: Available
*1
If trunk call is available, Account Code Entry (
®
1.5.4.3 Account Code Entry) is also available.
Note
DISA AA service and Operator Call (
®
2.2.5 Operator Features) are available for any security mode.
Security Mode Override by Verification Code Entry
If the caller performs Verification Code Entry (
®
1.9.6 Verification Code Entry) while hearing a DISA message,
the security mode can be temporarily changed to No Security mode.
Entry method:
Verification Code Entry feature + verification code + verification code PIN
After changing mode, the new mode remains in force for the duration of the call.
DISA Intercept Routing—Busy
If the first destination called by the outside party is busy, the call is redirected as follows:
a.
The call is redirected to the Intercept Routing—Busy destination assigned to the first destination.
b.
If an Intercept Routing—Busy destination is not assigned to the first destination and a prerecorded DISA
Busy Message is assigned, the caller will hear the DISA Busy Message.
c.
If neither an intercept destination nor a DISA Busy Message is assigned, the caller will hear a busy tone.
→
6.1 [4-1-1] Wired Extension—Extension Settings—Intercept Destination—
DISA Intercept Routing—DND
If the destination called by the outside party is in DND mode and Idle Extension Hunting is not available, one
of the following can be selected through system programming:
a.
Busy Tone:
The caller will hear a busy tone.
b.
Enable:
DND will redirect the call to the preprogrammed destination on an extension basis.
c.
OGM:
An outgoing message (OGM) will be sent to the caller. The message for DND mode can be assigned
for each outgoing message (OGM) which has a DISA floating extension number.
→
7.3 [5-3-1] Voice Message—DISA System—
DISA Intercept—Intercept when destination through DISA
DISA Intercept Routing—No Answer
If a destination is not available to answer a DISA call within a preprogrammed time period (DISA Intercept time)
after the call is reached, the call will be redirected to the programmed destination by the Intercept feature.
If the intercept destination is not available to answer the call within a preprogrammed time period (DISA
Disconnect Time after Intercept) after the DISA Intercept time expires, the call will be disconnected.
4.5 [2-3] Timers & Counters—DISA / Door / Reminder / U. Conf
196
Feature Guide
1.17.6 Direct Inward System Access (DISA)
Summary of Contents for KX-NCP500
