Service
Description & Reference
Malicious Call Identification
(MCID)
An extension user can ask the telephone company to trace a
malicious caller. Information on the malicious call will be received
later on.
®
1.21.1.9 Malicious Call Identification (MCID)
Completion of Calls to Busy
Subscriber (CCBS)
If a call is made to an outside party and the party is busy, an
extension can receive callback ringing when the called party
becomes free.
®
1.21.1.10 Completion of Calls to Busy Subscriber (CCBS)
3.
ISDN Centrex Service
An extension user can have access to the features of the ISDN Centrex Service of the telephone company
(e.g., Call Transfer). This is used by putting the current ISDN call on hold by sending a flash/recall signal.
This feature is enabled or disabled for each ISDN port.
®
3.33 [1-1] Slot—Port Property - BRI Port—ISDN CO—
®
3.35 [1-1] Slot—Port Property - PRI Port—CO Setting—
4.
Private Networking Connection (QSIG)
Private networking with QSIG is possible using an ISDN line. The QSIG mode, Master or Slave, can be
enabled on an ISDN port basis.
5.
ISDN Extension
(
®
An ISDN (BRI/PRI) port can be used for extension connection. While the extension connection is enabled,
ISDN terminal devices (e.g., ISDN telephone, G4 fax machine, PC) or a behind PBX can be connected to
the port.
When the ISDN port is in P-P configuration, one ISDN terminal device can be connected to the port.
When the ISDN port is in P-MP configuration, a maximum of eight ISDN terminal devices can be connected
to the port. However, only a maximum of two devices can be used simultaneously.
Conditions
•
Overlap/En bloc
For each ISDN port, either Overlap or En bloc can be selected as the dialling method for which the PBX
sends telephone numbers to the telephone company. The selected dialling method must be offered by the
telephone company. When "
Overlap
" is selected, the PBX sends each dialled digit individually.
When "
En bloc
" is selected, the PBX sends all of the dialled digits at once.
®
3.33 [1-1] Slot—Port Property - BRI Port—ISDN CO—
®
3.35 [1-1] Slot—Port Property - PRI Port—CO Setting—
In En bloc mode, the PBX recognises that the user is finished dialling when:
–
the # key is pressed (programmable).
®
4.18 [2-9] System Options—Option 2—
ISDN en Bloc Dial—[#] as End of Dial for en Bloc mode
–
the dialled number is a preprogrammed telephone number.
®
–
the inter-digit timer expires.
®
4.5 [2-3] Timers & Counters—Dial / IRNA / Recall / Tone—
•
Some supplementary services are provided by the key protocol (
®
1.21.1.12 ISDN Service Access by
•
Extension Number
An extension number can be assigned to each ISDN port.
®
6.1 [4-1-1] Wired Extension—Extension Settings—Main—
240
Feature Guide
1.21.1 Integrated Services Digital Network (ISDN)
Summary of Contents for KX-NCP500
