41
KX-NCP500GR
8 Test Mode
8.1.
Utility
8.1.1.
Utility-Diagnosis
Performs diagnostic tests on cards installed in the PBX, to identify the source of problems.
If any of the tests listed here returns the result "NG" ("No Good"), contact your dealer. Test results can be saved as a TXT-format
(text) file.
When testing is complete, any cards that were set to OUS status must be returned to INS status if they are to be used again.
8.1.1.1.
Card Test
Tests the relevant functions of a card to ensure that it is operating correctly. The tests carried out vary according to the type of card
being tested.
The tests that are performed on each card are as follows:
To perform a card test
1. From the Utility menu, select Diagnosis.
2. Click on the Status cell of the card to be tested, and set it to "OUS".
3. Click on the cell showing the card type.
A new window will be displayed.
4. Select the Card Test option.
A new window will be displayed.
5. Click OK to perform the test(s).
The error report will be displayed. When all tests are completed, the words "Test End!" will be shown on the last line of the out-
put.
6. Select an option:
• Click Capture if you want to save the displayed information.
1. Enter a file name, or select a file to overwrite.
2. Click Save.
• Click Cancel to return to the Diagnosis screen.
DHLC
DLC
SLC
LCOT
T1
E1
BRI
PRI
OPB
Local loop back diagnosis
X
X
X
X
X
X
X
X
Card CT bus diagnosis
X
X
X
X
X
X
X
X
X
DTMF Receive test port
X
X
PT loop back diagnosis
X
X
DSP DTMF generator/receiver diagnosis
X
X
DSP DTMF receiver diagnosis
X
X
Framer IC alarm signal detection diagnosis
X
X
X
Framer IC error detection diagnosis
X
X
X
CS-INF loop back diagnosis
Caller ID card loop back diagnosis
X
Extension mode setting test
X
Summary of Contents for KX-NCP500GR
