42
KX-NCP500GR
8.1.1.2.
Network Loopback Test
Performs a remote loopback test on the PRI23 card.
Note
• To perform this test, it is necessary to set Loopback Test started by Network in 3.28 [1-1] Slot -Port Property - PRI Port to
"Enable".
• The version of the PRI23 card must be 2.000 or later.
To perform a network loopback test
1. From the Utility menu, select Diagnosis.
2. Click on the Status cell of the PRI23 card, and set it to "OUS".
3. Click on the cell showing the card type.
A new window will be displayed.
4. Select the Loopback Type option.
A new window will be displayed.
5. Select Point1 or Point2 depending on the type of loopback test you want to perform.
The available selections may vary depending on the hardware version of the card.
6. Click Apply.
Preparation for the test is complete. The test will start automatically.
7. After the test is complete, select Release and click Apply.
8. Click Close to return to the Diagnosis screen.
8.1.1.3.
Utility-File Transfer PC to PBX (SD Card)
Copies PBX system files (program files, data files and activation key files) from the connected PC to the SD memory card installed
in the PBX. Pre-existing files on the SD memory card are overwritten.
This option is only available at Installer level.
The following types of files can be copied using this tool:
• Program files: These contain the programs used to operate cards within the PBX and CSs, acting as on-board drivers.
• Data files: These contain the initial configuration data for individual cards and settings.
• Activation Key files: These contain the activation keys used to enable the use of IP trunks and IP telephones through Virtual VoIP
cards and upgrade the software.
Not all files that are copied using this tool are automatically made active. To install new program files, main system data, or activa-
tion key for software upgrade to the PBX, use the System Reset-Reset by the Command utility for PBMPR, DBSYS, and LIC files.
Use the Activation Key button for other LIC files, and the SD Card File View and Load utility for all other files.
The PBX examines the header information of a file to determine 2 things: whether the file contains supported
data, and which system component the file applies to.
Only files whose header information matches that of a system file supported by the PBX can be transferred.
Attempting to transfer any other type of file results in an error message.
The names of all files that can be stored on the SD memory card are as follows:
Main Programme
*1 PBMPR-file-format data that is transferred to the PBX from the PC is saved as "PBMPR_S".
LPR Programme
Name on SD Memory Card
Corresponding Card
PBMPR
IPCMPR
PBMPR_S
IPCMPR*1
Name on SD Memory Card
Corresponding Card
PDHLC
DHLC4/DLC8/DLC16
PSLC
SLC8/SLC16
PT1
T1
PE1
E1
PBRI
BRI
PPRI23
PRI23
PPRI30
PRI30
POPB3
OPB
Summary of Contents for KX-NCP500GR
