Panasonic KX-NS1000 Feature Manual Download | Manualshive

Page: 378 / 482

background image

[Flowchart]

An extension user tries to
make a CO line call.

Was the number dialed using
System Speed Dialing?

What is the TRS level?

Is the dialed number found in an
applicable Denied Code Table?

Is the dialed number found in an
applicable Exception Code Table?

The call is denied.
The user hears a reorder tone.

Is TRS Override by
System Speed Dialing enabled?

The call is permitted.

Yes

Level 7

Level 1

Levels 2, 3, 4, 5, 6

Yes

Yes

Yes

No

No

No

No

Checks the TRS level of
the extension's COS for
System Speed Dialing.

Checks the TRS level of
the extension's COS in
the current time mode.

Denied Code Tables

Denied Code Tables are preprogrammed lists containing the first few digits (leading number) of telephone
numbers which may not be called. All outgoing CO line calls made by TRS level 2 through 6 users are compared
to at least one Denied Code Table, and when the leading number of a dialed telephone number (not including
the CO Line Access number) matches an entry found in the applicable table, the call is denied.
There are five Denied Code Tables. Each table applies to a corresponding TRS level as well as the level(s)
preceding it, as explained below.

378

Feature Manual

Document Version 2016-03

19.1.5 TRS (Toll Restriction)

«
...
376
377
378
379
380
...
»

Summary of Contents for KX-NS1000



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-NS1000

SIP IP PBX VOI-9300

Brand: LevelOne Pages: 61

Brand: LevelOne Pages: 73

Brand: Auerswald Pages: 200

Brand: Auerswald Pages: 1164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands