Panasonic KX-NS1000 Feature Manual Download | Manualshive

Page: 322 / 482

background image

Installation Manual References

4.4 Virtual Cards

PC Programming Manual References

9.12.2 PBX Configuration—[1-1] Configuration—Slot—Shelf Property - Virtual IP Gateway—Hunt Pattern
9.13 PBX Configuration—[1-1] Configuration—Slot—V-IPGW16—Port Property
17.1 PBX Configuration—[9-1] Private Network—TIE Table
18.4 PBX Configuration—[10-5] CO & Incoming Call—Miscellaneous—

Intercept—Routing to Operator -

No Destination (Destination is not programmed.)

Feature Manual References

2.1.3 ARS (Automatic Route Selection)
15.1.12 PRIVATE NETWORK FEATURES

15.1.24 PS (Portable Station)

Description

A Panasonic portable station (PS) can be used in place of a proprietary telephone (PT), providing wireless
access to PBX features and call handling.
Cell Stations (CSs) allow PSs to receive reception within a designated area.

1.

Registration

Before a PS can be used, it must be registered with the PBX through system programming and assigned
an extension number.

®

9.30 PBX Configuration—[1-2] Configuration—Portable Station—PS Registration and

De-registration—

Because a PS transmits radio waves, it is possible that a PS belonging to a neighboring PBX can be
registered to your PBX. To prevent this sort of unauthorized registration, a personal identification number
(PIN) can be programmed for this PBX that must be entered on the PS during registration. This PIN, if
programmed, is only used during the PS registration process.

®

9.30 PBX Configuration—[1-2] Configuration—Portable Station—PS Registration and

De-registration—

Personal Identification Number

Each PS can be registered to more than one PBX if necessary, and registration can be canceled if a PS
will no longer be used with one of these PBXs.

®

9.30 PBX Configuration—[1-2] Configuration—Portable Station—PS Registration and

De-registration—

De-registration

2.

Connection

There are two ways a PS can be used.

As an Extension

A PS is assigned its own extension number when it is registered to a PBX. The PS can use this extension
number to make and receive calls, just as a wired telephone can. A PS can be a member of an incoming
call distribution (ICD) group, can be assigned as the destination for redirected calls, etc., just as a wired
telephone can.
A PS can also be a member of a PS ring group (

®

15.1.27 PS—Ring Group). A PS ring group is a way

for several PSs to be notified of an incoming call simultaneously, but does not offer all of the features
provided by an ICD group. (

®

10.1.1 ICD GROUP FEATURES)

In Wireless XDP Parallel Mode

322

Feature Manual

Document Version 2016-03

15.1.24 PS (Portable Station)

«
...
320
321
322
323
324
...
»

Summary of Contents for KX-NS1000



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-NS1000

Quadro Quadro 2xi

Brand: Epygi Pages: 2

Brand: LG-Ericsson Pages: 92

Brand: Telesis Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands