Panasonic KX-NS1000 Feature Manual Download | Manualshive

Page: 79 / 482

background image

Feature

Description

CO-to-CO Line Call (except
Unattended Conference Call)
Duration

If a call between two outside parties is established, the call duration
can be restricted by the system timer selected for each trunk group.
Both parties will hear warning tones at five-second intervals starting
15 seconds before the time limit.

When the time limit expires, the

line will be disconnected.
If both parties involved in the CO-to-CO line call were established by
an extension (e.g., an extension makes a CO line call, then transfers
the call to an outside party), the time limit applied to the CO line call
that was made first will be used.

Dialing Digit Restriction
during Conversation

While engaged in an incoming CO line call, the dialing of digits can
be restricted. If the number of dialed digits exceeds the limitation, the
line will be disconnected.

*1

A party connected via an IP CO line or SIP CO line will not hear the warning tone.

Conditions

•

During an Unattended Conference Call, the Unattended Conference Recall time is applied. (

®

4.1.18 Conference)

•

When using LCO lines that do not support Calling Party Control (CPC) signal detection (

®

(Calling Party Control) Signal Detection), the CO-to-CO Line Call Duration timer should not be disabled,
as automatic end of call detection cannot be performed.

PC Programming Manual References

10.7.1 PBX Configuration—[2-7-1] System—Class of Service—COS Settings—CO & SMDR— Extension-CO
Line Call Duration Limit
10.9 PBX Configuration—[2-9] System—System Options—Option 2—

Extension - CO Call Limitation—For

Incoming Call
11.1.1 PBX Configuration—[3-1-1] Group—Trunk Group—TRG Settings—Main

CO-CO Duration Time (*60s)

Extension-CO Duration Time (*60s)

15.5 PBX Configuration—[7-5] TRS—Miscellaneous—

Dial Digits Limitation After Answering—Dial Digits

Feature Manual References

4.1.22 COS (Class of Service)

4.1.18 Conference

Description

An extension user can establish a conference call by adding additional parties to an already existing two-party
conversation. This PBX supports three-party through eight-party conference calls. Conferences with more than
four parties are only possible when a PT or PS user originates the conference.

Unattended Conference:

The conference originator can leave the conference and allow other parties to continue. Establishing an
Unattended Conference allows the originator to return to the conference. Unattended Conferences can only
be established by PT and PS users.

Document Version 2016-03

Feature Manual

79

4.1.18 Conference

«
...
77
78
79
80
81
...
»

Summary of Contents for KX-NS1000



































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-NS1000

Brand: Well Pages: 8

Brand: Well Pages: 13

Brand: Aastra Pages: 2

OpenCom 100 series

Brand: Aastra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands