5.
It is strongly recommended that passwords of 10 numbers or characters be used for maximum
protection against unauthorised access. For a list of numbers and characters that can be used in system
passwords, refer to "1.1.3 Entering Characters" in the PC Programming Manual.
Connecting to Web Maintenance Console
1.
Connect the PC to the PBX:
•
Connect the PBX to a network with the LAN port and access the PBX from a PC in your LAN or VPN.
For details, refer to "Connection via LAN", "Connection via Virtual Private Network (VPN) " and
"4.11.1 LAN Connection for the Main Unit".
•
Connect the PBX to a network with the LAN port and access the PBX from a PC using an Internet
connection. For details, refer to "Connection via Internet" and "4.11.1 LAN Connection for the Main
Unit".
•
Connect the PBX to a PC through analogue remote (RMT card) or ISDN remote. For detail, refer to
"5.5.2 PC Programming" in the Feature Guide.
2.
Access Web Maintenance Console:
LAN or VPN Connection:
Launch your Web browser and input the IP address of the PBX followed by the Web Maintenance Console
port number into the address bar. The input method will differ according to the PC’s connection to the PBX.
The default IP address for the LAN port of the PBX is 192.168.0.101, and the default Web Maintenance
Console port number is 80. Accordingly, the address to enter to connect to the PBX for the first time will
be as follows (enter the address exactly as shown):
http://192.168.0.101
Note
The default subnet mask for the LAN port is 255.255.255.0.
MNT Port Connection:
Launch your Web browser and in the address bar, enter one of the following addresses exactly as shown:
–
223.0.0.1
or
–
http://kx-ns300.
Note
•
If entering "http://kx-ns300.", be sure to include the period at the end as shown.
•
The default subnet mask for the MNT port is 255.255.255.0.
•
If it takes a long time to connect when 223.0.0.1 is entered, configure a static IP address to the
LAN connected to the PC.
Internet Connection (SSL Connection):
When the PC is accessing the PBX from a connection over the internet, the use of SSL is strongly
recommended. When using an SSL encrypted connection, the default port is 443. The format of the address
to enter to connect to the PBX using an SSL encrypted connection will be as follows:
https://xxx.xxx.xxx.xxx:yyy
•
"
xxx.xxx.xxx.xxx
" is the IP address of a device that can be accessed from the Internet, such as the
IP address of a network router.
•
"
yyy
" is a port number. The network router’s port forwarding settings must be configured so that traffic
arriving at port "yyy" is forwarded to the correct IP address and port of the PBX in the LAN.
•
Port forwarding settings must specify the IP address and the port number of the network router
("
xxx.xxx.xxx.xxx:yyy
") to transfer the packets to the PBX in the LAN, so that the packets sent to the
global IP address and specified port of the router will be transferred to the IP address and specified
port of the PBX in the LAN.
Installation Manual
157
5.3 Starting Web Maintenance Console
Summary of Contents for KX-NS300
