Composition:
PI0 (IC4)
IC24, IC26, IC28, IC30, etc.
Circuit Operation:
This circuit is a circuit which detects the end of call at CO-CO call.
It converts whether the voice exits or not into the logic level (IC24, 26, 28, 30), then presents it to
CPU (IC1) through P10 (IC4). There are three methods for detecting the end of call as follows.
- No tone detection
- Cyclic tone detection
- Continuous tone detection
The four of this circuit are installed corresponding to each time slot of TS16~19.
Highway Control Circuit
Composition:
IC37, IC42, IC43, IC67, IC71
Circuit Operation:
This circuit is a circuit which transfers the data in the HWS 6 of the down highway onto HWR 6 of
the up highway for calling between CO and CO. TS16~19 are controlled individually.
The CPU (IC1) controls the gate IC (IC34, 42, 43, 67, 71) through PI0 (IC4), connects DHW 6 and
UHW 6.
Timing Signal Generator Circuit
Composition:
IC39, IC40, IC62, IC63, IC64, IC65
Circuit Operation:
This circuit is a circuit which generates the timing signals for using for ADPCM, CODEC Circuit
and Highway Control Circuit. These signals are generated from the channel select signals
(CH0~4) and the highway clock (C2M, C4MN) which are presented from the CPU BOARD.
48
Summary of Contents for KX-TA1232
