background image

PLEASE READ BEFORE USE
AND SAVE.

Cordless Phone

Model No.  

KX-TC1200ALB

KX-TC1200ALW/KX-TC1200ALS

KX-TC1200ALF/KX-TC1200NZB

KX-TC1200NZW/KX-TC1200NZF

Operating Instructions

Charge the battery for about 

15 hours before initial use.

1 Getting Started
2 Making/Answering Calls
3 Speed Dialler
4 One-Touch Dialler
5 Special Features
6 Things You Should Know

Contents by Section

WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO LIQUID OR ANY TYPE OF MOISTURE.
When a failure occurs which results in the internal parts becoming accessible, disconnect
AC adaptor immediately and return this unit to the place of purchase or service centre.
If there is any trouble, disconnect the unit from the telephone line and connect a
known working phone. If the known working phone operates properly, do not
reconnect the unit to the telephone line until the fault has been repaired. If the
known working phone does not operate properly, consult your telephone company.
This equipment has been tested and found to comply with AS/NZS 3548:1995 limits
for electromagnetic interference. Any modifications to any part of the system or to any
peripherals may void the EMC compliance of the system or the peripherals.
This equipment will be inoperable if mains power fails.

WARNING:
The earcap on the handset is magnetised and may retain metallic objects.

KX-TC1200ALB

Kyushu Matsushita Electric Co., Ltd.
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan

PQQX13174ZA-BM F0801-1091  

D

For your future reference

Serial No.

Date of purchase

(found on the bottom of the unit)

Name and address of dealer

For New Zealand Users Only

The grant of a Telepermit for any item of terminal equipment indicates only that Telecom
has accepted that the item complies with minimum conditions for connection to its
network. It indicates no endorsement of the product by Telecom, nor does it provide any
sort of warranty. Above all, it provides no assurance that any item will work correctly in
all respects with another item of Telepermitted equipment of a different make or model,
nor does it imply that any product is compatible with all of Telecom’s network services.

WARNING NOTICE:
No “111” or other calls can be made from this device during a mains power failure.
This equipment shall not be set to make automatic calls to the Telecom “111”
Emergency Service.

We recommend that a standard phone which can be used in the case of a power failure
be connected to the telephone line at all times.

Attach or keep original receipt to assist with any repair under warranty.

Summary of Contents for KX-TC1200ALB









Reviews: