(AUTO)
(RECALL)
(PAUSE)
(PROGRAM)
(TALK)
and
Indicator
IN USE/CHARGE Indicator
(HANDSET!LOCATOR)
5-A Handset Locator
You can locate the handset or page the handset user with beep tones.
1
Press
(HANDSET!LOCATOR)
on the base unit.
•
The IN USE/CHARGE indicator flashes and the handset beeps for 1 minute.
2
To stop paging, press
(HANDSET!LOCATOR)
again or press
(TALK)
twice on the handset.
5-B Automatic Security Code Setting
Whenever you place the handset on the base unit, the unit automatically selects one of 65,000 security
codes. These codes help prevent the unauthorized use of your telephone line by another cordless
telephone user.
5-C Using the PAUSE Button
(For PBX Line/Long Distance Calls)
We recommend you press
(PAUSE)
if a pause is required for dialling with a PBX or to make a long
distance call.
Eg: Line access number
(9)
(PBX)
(9)
\
(PAUSE)
\
•
Pressing
(PAUSE)
once creates a 3.5 second pause. This prevents misdialling when you redial or dial
a stored number.
•
Pressing
(PAUSE)
more than once increases the length of the pause between numbers.
5-D RECALL Button
Pressing
(RECALL)
allows you to use special features of your host PBX such as transferring an
extension call or accessing optional telephone services such as call waiting.
Selecting the recall time
The recall time depends on your telephone exchange or host PBX. You can select the following recall
times: “90, 100, 110, 250, 300, 400, 600 or 700 msec (milliseconds)”. KX-TC2000AL comes from the
factory set to “100 msec” and KX-TC2000NZ comes set to “600 msec”.
The TALK indicator light must be off before programming.
Press
(PROGRAM)
\
\
(AUTO)
\
(RECALL)
.
•
A beep sounds.
•
If 3 beeps sound after programming, a wrong key was pressed. Start again from the beginning.
•
Users in Australia can access Telstra’s “EASY CALL” service by having the recall time set at 100
msec (this is the factory default setting), and then follow Telstra’s “EASY CALL” instructions to operate
this service.
•
If the unit is connected via a PBX, PBX functions (transferring a call etc.) might not work correctly.
Consult your PBX supplier for the correct setting.
•
When you receive a second call during a conversation, you will hear a signal tone following the call
waiting tone and the conversation will be interrupted for approximately a second. The tones are
generated from the telephone company. This is not fault of the product as these events are normal.
1
: 90 msec
2
: 100 msec
3
: 110 msec
4
: 250 msec
5
: 300 msec
6
: 400 msec
7
: 600 msec
8
: 700 msec
1
8
Dialling button ( to )
Phone number
6-B Base Unit Location
Calls are transmitted between the base unit and the handset using wireless
radio waves.
For maximum distance and noise-free operation,
the
recommended base unit location is:
6-C Wall Mounting
This unit can be mounted on a wall.
Away from electrical appliances
such as a TV, personal computer,
cellular phone charging units
or another cordless phone.
In a HIGH and CENTRAL
location with no obstructions
such as walls.
Extend
fully.
1
Pull down the handset
hook until it locks,
so the
tab holds the handset.
2
Press the tabs in
the direction of the
arrows (
#
), then
remove the wall
mounting adaptor
(
$
).
6-E Safety Instructions
Take special care to follow the safety suggestions listed below.
6-D Troubleshooting
Problem
The unit does not work.
An alarm tone sounds
when you press
(TALK)
.
Static, sound cuts in/out,
fades.
Interference from other
electrical units.
The unit does not ring.
Cause and Remedy
•
Check the settings (1-C).
•
Charge the battery fully (6-A).
•
Clean the charge contacts and charge
again (6-A).
•
Install the battery properly (1-C, 6-A).
•
Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.
•
Re-insert the handset battery and place
the handset on the base unit. Try again.
•
KX-TC2000AL and KX-TC2000NZ are not
designed to be used with rotary (pulse
dialling) services.
•
You are too far from the base unit.
Move closer and try again.
•
Place the handset on the base unit and try
again.
•
Plug in the AC adaptor.
•
Extend the base unit antenna fully.
•
Locate the handset and the base unit away
from other electrical appliances (6-B).
•
Move closer to the base unit.
•
Extend the base unit antenna fully.
•
Press
(CH)
to select a clearer channel.
•
The ringer volume is set to OFF.
Press
(RINGER)
when the TALK indicator
light is off (2-B).
Problem
While storing a phone
number, the unit starts
to ring.
You cannot store a
phone number in
memory.
You cannot redial by
pressing
(REDIAL)
.
(HANDSET!LOCATOR)
does not function.
The RECHARGE
indicator flashes or the
unit beeps intermittently.
You charged the battery
fully, but the RECHARGE
indicator flashes.
The IN USE/CHARGE
indicator light does not
go out while charging.
Cause and Remedy
•
To answer the call, press
(TALK)
.
The program will be cancelled. Store the
number again.
•
You cannot store a number while the unit
is in the talk mode.
•
Do not pause for over 60 seconds while storing.
•
If the last number dialled was more than 24
digits long, the number will not be redialled.
•
The handset is too far from the base unit
or is engaged in an outside call.
•
Charge the battery fully (6-A).
•
Clean the charge contacts and charge
again (6-A).
•
Install a new battery (6-A).
•
This is normal.
PLEASE READ BEFORE USE
AND SAVE.
Cordless Phone
Operating Instructions
Model No.
KX-TC2000ALB
KX-TC2000ALF/KX-TC2000ALS
KX-TC2000ALW/KX-TC2000NZB
KX-TC2000NZF/KX-TC2000NZW
Charge the battery for about
15 hours before initial use.
1 Getting Started
2 Making/Answering Calls
3 Speed Dialler
4 One-Touch Dialler
5 Special Features
6 Things You Should Know
Contents by Section
5) The maximum calling distance may be shortened when the unit is used in the
following places: Near obstacles such as hills, tunnels, undergrounds, near metal
objects such as wire fences, etc.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO LIQUID OR ANY TYPE OF MOISTURE.
When a failure occurs which results in the internal parts becoming accessible, disconnect
AC adaptor immediately and return this unit to the place of purchase or service centre.
If there is any trouble, disconnect the unit from the telephone line and connect a
known working phone. If the known working phone operates properly, do not
reconnect the unit to the telephone line until the fault has been repaired. If the
known working phone does not operate properly, consult your telephone company.
This equipment has been tested and found to comply with AS/NZS 3548:1995 limits for
electromagnetic interference. Any modifications to any part of the system or to any
peripherals may void the EMC compliance of the system or the peripherals.
This equipment will be inoperable if mains power fails.
WARNING:
The earcap on the handset is magnetised and may retain metallic objects.
Panasonic Communications Co., Ltd.
1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan
PQQX13660ZA
S0503-1074
5
Special Features
Section 5
6
Things You Should Know
Things You Should Know
Section 6
Screws (not included)
Hooks
8.3 cm
For Australia
To Telephone Plug
and Socket
OR
For New Zealand
To Single-Line
Telephone Jack
3
Connect the AC adaptor.
Tuck the telephone line cord
inside the wall mounting
adaptor, then push it in the
direction of the arrows
(
#
and
$
).
•
The word “UP WALL”
should face upward.
4
Connect the telephone
line cord. Install screws
using the wall template
below. Mount the unit,
then slide down.
•
Extend the antenna fully.
•
Fasten the cords to prevent it
from being disconnected.
2
1
1
1
2
To Power
Outlet
Safety
1) The unit should be connected to a power supply only of the type described in the
operating instructions or as marked on the unit.
2) When left unused for a long period of time, the base unit should be unplugged
from the household AC outlet.
3) To minimize the possibility of lightning damage when you know that a
thunderstorm is coming, we recommend that you:
a) Unplug the telephone line cord from the phone jack.
b) Unplug the power supply cord from the AC power outlet.
Installations
Environment
1) Do not use this unit near liquids—for example, near a bathtub, washbowl, sink,
etc. Damp environments should also be avoided.
2) The unit should be kept away from heat sources such as heaters,
kitchen stoves, etc. It also should not be placed in rooms where the
temperature is less than 5°C or greater than 40°C.
3) The AC adaptor is used as the main disconnect device, ensure that the AC outlet
is located/installed near the unit and is easily accessible.
Placement
1) Do not place heavy objects on top of this unit.
2) Care should be taken so that objects do not fall onto, and liquids are not spilled into, the
unit. Do not subject this unit to excessive smoke, dust, mechanical vibration, or shock.
3) Place the unit on a flat surface.
For best performance
1) If noise prevents the conversation from being understood at the handset,
approach the base unit to lessen the noise.
2) The handset should be used at the HIGH volume setting when the reception
audio is difficult to hear.
3) The handset should be fully recharged on the base unit when the RECHARGE
indicator flashes.
4) The handset antenna should not be touched during use because it can effect the
handset’s performance.
6-F Specifications
■
Base unit
Power Supply:
AC Adaptor (230-240 V AC, 50/60 Hz)
Power Consumption:
Standby:
Approx. 5 W
Maximum:
Approx. 7 W
Frequency:
30 MHz – 39 MHz
Dimensions (H x W x D):
Approx. 80 mm x 125 mm x 210 mm
Mass (Weight):
Approx. 300
g
■
Handset
Power Supply:
Ni-Cd battery (3.6 V, 300 mAh)
Frequency:
30 MHz – 39 MHz
Dimensions (H x W x D):
Approx. 278 mm x 54 mm x 40 mm
Mass (Weight):
Approx. 190
g
Security Codes:
65,000
■
Operating Environment:
5 ˚C – 40 ˚C
Specifications are subject to change without notice.
8.3 cm
Wall Template
KX-TC2000ALB
For Call Waiting Service Users in New Zealand
Make sure the recall time is set to 600 msec for use with Telecom’s Call Waiting Service. Press
(RECALL)
if you hear a call-waiting tone while talking.
•
The first call is put on hold and you can answer the second call.
•
To return to the first caller, press
(RECALL)
again.
For Australia Customers
Panasonic Australia operates a toll free Customer Support Centre.
Please phone Panasonic on 132600 for assistance.
For New Zealand Customers
Panasonic New Zealand operates our Customer Support Centre.
Please phone (09) 272 0178 for assistance.
For New Zealand Users Only
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom
has accepted that the item complies with minimum conditions for connection to its
network. It indicates no endorsement of the product by Telecom, nor does it provide any
sort of warranty. Above all, it provides no assurance that any item will work correctly in all
respects with another item of Telepermitted equipment of a different make or model, nor
does it imply that any product is compatible with all of Telecom’s network services.
WARNING NOTICE:
No “111” or other calls can be made from this device during a mains power failure.
This equipment shall not be set to make automatic calls to the Telecom “111”
Emergency Service.
•
We recommend that a standard phone which can be used in the case of a power
failure be connected to the telephone line at all times.
•
This equipment should not be used under any circumstances which may
constitute a nuisance to other Telecom customers.
For your future reference
Serial No.
Date of purchase
(found on the bottom of the unit)
Name and address of dealer
Attach or keep original receipt to assist with any repair under warranty.
6-A Battery
Recharge
When the RECHARGE indicator flashes
or the unit beeps intermittently, place the
handset on the base unit for about
15 hours to recharge the battery.
Battery information
After your Panasonic battery is fully charged:
While in use (TALK)
While not in use (Standby)
Up to about 5 hours
Up to about 14 days
RECHARGE
Indicator
•
The battery operating time may be shortened depending on usage
conditions and ambient temperature.
•
As preventative maintenance, clean the handset and the base
unit charge contacts with a soft, dry cloth once a month.
Clean more often if the unit is subject to grease, dust or
humidity.
Otherwise the battery may not charge properly.
•
If the battery is fully charged, you do not have to place the handset
on the base unit until the RECHARGE indicator flashes. This will
maximize the battery life.
•
The battery cannot be overcharged.
Operation
Operating time
Battery replacement:
If you cleaned the charge contacts and fully charged the battery,
but after a few telephone calls, the RECHARGE indicator flashes,
the battery needs to be replaced. Replace the battery with a new
Panasonic P-P301 (KX-A36A) battery. See section 1-C, step 2.
When replacing the battery, programmed information may be
erased. Reprogram if necessary.
