Panasonic KX-TD816 User Manual Download

Page: 304 / 388

Station Features and Operation (DPT/SLT)

304

User Manual

4.4.9

Timed Reminder, Remote (Wake-Up Call)

The Manager and the Operators can remotely set or cancel the Timed Reminder to the desired
extension.

Setting

7235 / 7436

Dial the desired extension
number or press DSS

(flexible button).

Hang up or press
SP-PHONE.

Enter the minute
(00 through 59).

hour

minute

For AM: Dial 0.
For PM: Dial 1.

For one time alarm*

: Dial 0.

For daily alarm*

: Dial 1.

Confirmation
tone and dial tone

extension no.

Enter the hour
(01 through 12).

(DSS)

Press NEXT (S3).

S 1

S 2

S 3

S 1

S 2

S 3

PROG

Press PROG (S3)

<PT Display Example>

Extension #:

<PT Display Example>

Extension #:

<PT Display Example>

(xxxx: extension number)

Extension #:xxxx

Time(hh:mm): :

AM/PM(0/1) :

Daily Y/N(1/0):0

Press Features.

Rotate Jog Dial or press
NEXT until the following
is displayed.

Press Remote Timed Reminder.

Features

Remote Timed Reminder

You hear an alarm ringing at the preset time and then the setting is cleared.

You hear an alarm ringing daily at the preset time until the setting is changed or canceled.

<PT Display Example>

Alarm 01:00AM

– only one time

Alarm 01:00AM

– daily

Summary of Contents for KX-TD816





































































































































































































































































































































































































Search results

Summary of Contents for KX-TD816

Reviews:

Related manuals for KX-TD816

Brands by name

Popular brands

Panasonic KX-TD816, User Manual

Search results

Summary of Contents for KX-TD816

Reviews:

Related manuals for KX-TD816

Brands by name

Popular brands