Panasonic KX-TD816 User Manual Download | Manualshive

Page: 381 / 388

background image

APPENDIX

User Manual

381

6.1.4

Troubleshooting

If a power failure should occur...

Your System enables conversations between specific outside lines and extensions (Power
Failure Transfer), and supports system data backup.

Power Failure Transfer

Specific extensions are automatically connected straight to specific outside lines. This
provides outside line conversations between the pre-assigned extensions and analog outside
lines:

<KX-TD816>

Outside line 01 is connected to extension jack number 01.

Outside line 02 is connected to extension jack number 02.

Outside line 05 is connected to extension jack number 09.

Outside line 06 is connected to extension jack number 10.

<KX-TD1232>

Outside line 01 is connected to extension jack number 01.

Outside line 02 is connected to extension jack number 02.

Outside line 03 is connected to extension jack number 09.

Outside line 04 is connected to extension jack number 10.

Outside line 09 is connected to extension jack number 17.

Outside line 10 is connected to extension jack number 18.

•

All other conversations are disconnected during a power failure.

•

Digital proprietary telephones (DPTs) cannot be used during a power failure. SLTs can
work in the event of a power failure.

•

When power is restored after a power failure, your system automatically restarts
operation, maintaining as much of the previous system data as possible.

Problem

Probable Cause

Possible Solution

Nothing is heard in the hands-
free mode.

The "Headset" mode is
selected.

When the headset is not used, set
the mode to "Handset".
Refer to "Handset/Headset
Selection" in Station
Programming (Section 2), or
"Initial Setting" (Section 1).

«
...
379
380
381
382
383
...
»

Summary of Contents for KX-TD816





































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-TD816

Brand: Panasonic Pages: 278

Communication Server 1000M

Brand: Nortel Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands