background image

Planning

32

Installation Manual

Trunk Group (ITRK)

Use the Trunk Group Field to define from 1 to 2 Trunk Groups to be associated with the KX-
TDA0480: Trunk Group 1 and Trunk Group 2.

A Trunk Group consists of a collection of trunks on the KX-TDA0480. At least one group must 
be defined and up to four Trunk Groups (ports 1 to 2) can be defined for the KX-TDA0480.

Trunk Groups

In the sample, the Trunk Group parameter for all ports is recorded as the default, 1 (e.g., All 
ports are members of the same Trunk Group).

Delete Digits (TGNINFO)

Use the Delete Digits field to record the number of digits to be deleted from the received 
number.

In the sample, the Delete Digits parameter for all ports is configured to the default value of 0.

Length of Call Reference (ITRK)

This parameter must always be set to "1".

Interface Type (ITRK)

This parameter must always be set to "Basic Interface".

KX-TDA0480

PBX main unit

1 Trunk group

Port 1

Port 2

2 Trunk groups

Port 1

Port 2

Summary of Contents for KX-TDA0480















































































































































































Reviews: