Signal Name
Function
+15VIN
+15V DC
+15V
For C15V DC MOH
+9.4V
For Driver IC +9.4V DC RS-232C
+5V
For Driver IC +5V DC RS-232C
+5VRMT
Reserve
3.3V_BB
+3.3V DC
For pull-up of back board signal line
+3.3VB
+3.3V DC
Backup by a battery
For SRAM (IC301, IC302) backup
+3.3V
+3.3V DC
1.9VB
+1.9V DC
Backup by a battery
For clock function of CPU (IC100)
1.8V
For Core +1.8V DC CPU (IC100)
A[0]-A[25]
Address bus
nAC_ALM
AC alarm signal: This indicates AC voltage cutoff. (L: Alarm condition)
nBACK
Bus Acknowledge: This indicates Bus Acknowledge.
nBATT
This indicates whether external battery is connected or not.L: Connected
nBAT_ALM
Battery Alarm Signal: This indicates the declined voltage of lithium battery. (L:
condition)
nBREQ
Bus Request: Bus request signal
nBS
Bus Cycle Start: Bus cycle start signal
nCASL
Lower Byte Address Column Address Strobe: CAS signal for SDRAM
nCASU
Upper Byte Address Column Address Strobe: CAS signal for SDRAM
CH_SEL[0]
Synchronous Signal for CODEC (For MOH#1/Page#1)
CH_SEL[1]
Synchronous Signal for CODEC (For MOH#2/Page#2)
CH_SEL[2]
Synchronous Signal for CODEC (For RMT)
CKE
Clock Enable: CKE signal for SDRAM
CKIO
Clock I/O Terminal: For bus clock of SDRAM (IC305, IC306) and ASIC (IC101) CPU
(IC100) outputs the clock of four times frequency as many as Source clock (16.384MHz).
nCS0
Chip Select 0: Chip select signal for flash memory
nCS2
Chip Select 2: Chip select signal for the expanded SDRAM (Future Option, Reserve
present.)
nCS3
Chip Select 3: Chip select signal for SDRAM
nCS4
Chip Select 4: Chip select signal for SRAM
nCS5
Chip Select 5: Chip select signal for ASIC
nCS6
Chip Select 6: Chip select signal for USB I/F and SD card I/F
nCS_FLASH0
Chip Select for Flash memory0: CS signal for IC303
nCS_FLASH1
Chip Select for Flash memory1: CS signal for IC304 (reserve)
nCS_SDB0
Chip Select for Sd card I/F
nCS_SDB1
Reserve
33
Summary of Contents for KX-TDA100AL
