Panasonic KX-TDA15 Features Manual Download

Page: 219 / 420

1.18 Proprietary Telephone (PT) Features

Feature Guide

219

Log-in/Log-out *

Used to switch between log-in and log-out mode.

Hurry-up

Used to redirect the longest waiting call in the queue of an incoming
call distribution group to the overflow destination.

Wrap-up *

Used to switch the Wrap-up/Not Ready and Ready modes.

System Alarm

Used to confirm a PBX error.

Time Service *

Used to switch the assigned time modes: day, lunch, break or night.
Also used to check the current time mode status.

Answer

Used to answer an incoming call.

Release

Used to disconnect the line during or after a conversation, or to
complete a Call Transfer.

Toll Restriction/Call Barring

Used to change the TRS/Barring level of other extension users
temporarily.

ISDN Service

Used to access an ISDN service.

Calling Line Identification
Restriction (CLIR) *

Used to switch between the CLIP and CLIR service.

Connected Line Identification
Restriction (COLR) *

Used to switch between the COLP and COLR service.

ISDN Hold

Used to transfer a call using the telephone company.

Headset

Used to turn on/off the headset mode while idle.
Used to switch between hands-free mode and headset modes during
a conversation.

Time Service Switching Mode
(Automatic/Manual) *

Used to switch between the Automatic Switching and Manual
Switching mode.

Two-way Record

Used to record a conversation into your own mailbox.

Two-way Transfer

Used to record a conversation into the mailbox of a specified
extension.

One-touch Two-way Transfer

Used to record a conversation into the mailbox of a specified extension
with one touch.

Live Call Screening (LCS)

Used to monitor your own voice mailbox while an incoming caller is
leaving a message and, if desired, intercept the call.

Voice Mail (VM) Transfer

Used to transfer a call to the mailbox of a specified extension.

Check-in

Used to switch the status of extensions from Check-out to Check-in.

Check-out

Used to switch the status of extensions from Check-in to Check-out.

CTI

Used to access CTI features.

One-touch Feature Setting Buttons:

Pressing these buttons while on-hook changes the feature

settings. The new mode will be displayed for a preprogrammed time period.

Button

Usage

Summary of Contents for KX-TDA15





































































































































































































































































































































































































































Search results

Summary of Contents for KX-TDA15

Reviews:

Related manuals for KX-TDA15

Brands by name

Popular brands

Panasonic KX-TDA15, Features Manual

Search results

Summary of Contents for KX-TDA15

Reviews:

Related manuals for KX-TDA15

Brands by name

Popular brands