26
Programming
4
Proceed with the operation for your unit.
Handset:
L
OFF
R
to return to standby.
Base unit:
L
EXIT/STOP
R
to return to standby.
Change PIN
Some functions are protected by a 4-digit PIN
code which must be entered if the settings are
changed. The default PIN is 0000. The PIN can
be changed to a preferred number.
When entering a PIN, the digits are shown as
****.
Handset / Base unit
1
L
Menu
R
,
L
d
R
“Advanced set”
, press
L
OK
R
.
2
L
d
R
“Change PIN”
, press
L
OK
R
.
3
If the PIN is already changed from default
setting, enter the current 4-digit PIN, press
L
OK
R
.
4
Enter a new 4-digit PIN, press
L
OK
R
.
5
Re-enter the new PIN, press
L
OK
R
to save.
6
Proceed with the operation for your unit.
Handset:
L
OFF
R
to return to standby.
Base unit:
L
EXIT/STOP
R
to return to standby.
IMPORTANT
If the PIN code is changed, please keep a record
of the new number.
Registering a handset
Note:
● Handset batteries must be fully charged
before registration. Hold the handset close to
the base unit during the registration process.
Handsets that were supplied with the base
unit are already pre-registered.
On the base unit:
1
Press and hold
L
LOCATOR/INTERCOM
R
for 5 seconds. The base unit will remain in
registration mode for 120 seconds.
On the handset:
2
If the handset is not registered to a base
unit: “
Register your
Handset”
, press
L
OK
R
.
“Press locator Key for 5 sec”
, press
L
OK
R
and then enter the 4-digit PIN code (default =
0000),
L
OK
R
.
3
If the handset is already registered to a base
unit, press
L
Menu
R
,
L
d
R
“Advanced set”
,
press
L
OK
R
.
L
d
R
“Register”
, press
L
OK
R
.
4 “Press locator key for 5 sec”
, press
L
OK
R
.
● If you want to change/delete the block list
number, follow the first 3 steps in “Adding
call
blocked number manually”
on page 25
, and
then press
L
s
R
to the slot where the number
is
stored, press
L
OK
R
. To delete the number,
press
L
CLEAR
R
, either press
L
OK
R
to delete, or
enter a new number and press
L
OK
R
.
Flash time
This setting is useful to access certain network
and PBX/switchboard services. The default flash
time is suitable for your country and network
operator. It is unlikely that you should need to
change this setting unless advised to do so.
Handset / Base unit
1
L
Menu
R
,
L
d
R
“Advanced set”
, press
L
OK
R
.
2
L
d
R
“Flash time”
, press
L
OK
R
.
3
L
s
R
: Select
“80ms”, “90ms”, “100ms”,
“110ms”, “160ms”, “200ms”, “250ms”,
“300ms”, “400ms”, “600ms”, “700ms”
or
“900ms”,
press
L
OK
R
to save.
4
Proceed with the operation for your unit.
Handset:
L
OFF
R
to return to standby.
Base unit:
L
EXIT/STOP
R
to return to standby.
Dial mode
Your phone is set to tone dialing. You should
only need to change this if connected to a PBX/
switchboard which requires pulse dialing.
Handset / Base unit
1
L
Menu
R
,
L
d
R
“Advanced set”
,
L
OK
R
.
2
L
d
R
“Dial mode”
,
L
OK
R
.
3
L
s
R
: Select
“Tone”
or
“Pulse”
,
L
OK
R
.
4
Proceed with the operation for your unit.
Handset:
L
OFF
R
to return to standby.
Base unit:
L
EXIT/STOP
R
to return to standby.
Auto clock
If you have subscribed to Caller ID Service,
the date and time will be set on your base unit
whenever a call is received. This feature can be
set to On or Off.
Handset / Base unit
1
L
Menu
R
,
L
d
R
“Advanced set”
, press
L
OK
R
.
2
L
d
R
“Auto clock”
, press
L
OK
R
.
3
L
s
R
: Select
“On”
or
“Off”
, press
L
OK
R
to save.
