manualshive.com logo in svg

Panasonic KX-TGCA20EX, Service Manual

The Panasonic KX-TGCA20EX {Keywords: Service manual, manual, download, free} offers a convenient way to access user instructions for your Panasonic cordless phone. With just a few clicks, you can effortlessly download the service manual from 88.208.23.73:8080, allowing you to effortlessly troubleshoot and optimize your device's performance.

Share
Download
background image

3

KX-TGC210/KX-TGC212/KX-TGC213/KX-TGC220/KX-TGC222/KX-TGCA20

TABLE OF CONTENTS

PAGE

PAGE

1 Safety Precautions

-----------------------------------------------

5

1.1. For Service Technicians --------------------------------- 5

2 Warning

--------------------------------------------------------------

5

2.1. Battery Caution--------------------------------------------- 5
2.2. About Lead Free Solder (PbF: Pb free)-------------- 5

2.2.1. Suggested PbF Solder ------------------------------ 6

2.3. Discarding of P. C. Board-------------------------------- 6

3 Specifications

-----------------------------------------------------

7

4 Technical Descriptions

-----------------------------------------

8

4.1. Block Diagram (Base Unit_Main)---------------------- 8
4.2. Circuit Operation (Base Unit) --------------------------- 9

4.2.1. Outline --------------------------------------------------- 9

4.3. Block Diagram (Base Unit_RF Part) -----------------10
4.4. Circuit Operation (Base Unit) -------------------------- 11

4.4.1. BBIC (Base Band IC: IC501) --------------------- 11
4.4.2. Flash Memory (IC601)(for KX-TGC220

only) ----------------------------------------------------- 11

4.4.3. EEPROM (IC611) ------------------------------------ 11
4.4.4. Power Supply Circuit/Reset Circuit--------------12
4.4.5. Telephone Line Interface---------------------------14
4.4.6. Transmitter/Receiver--------------------------------14

4.5. Block Diagram (Handset)-------------------------------16
4.6. Circuit Operation (Handset)----------------------------17

4.6.1. Outline --------------------------------------------------17
4.6.2. Power Supply Circuit/Reset Circuit--------------17
4.6.3. Charge Circuit ----------------------------------------17
4.6.4. Battery Low/Power Down Detector--------------17
4.6.5. Speakerphone ----------------------------------------17

4.7. Signal Route -----------------------------------------------18

5 Location of Controls and Components

------------------

20

6 Installation Instructions

---------------------------------------

20

7 Operating Instructions

-----------------------------------------

20

7.1. For Service Hint-------------------------------------------20

8 Test Mode

----------------------------------------------------------

21

8.1. Engineering Mode ----------------------------------------21

8.1.1. Base Unit ----------------------------------------------21
8.1.2. Handset ------------------------------------------------23

8.2. EEPROM LAYOUT (Handset)-------------------------25

8.2.1. Scope ---------------------------------------------------25
8.2.2. Introduction--------------------------------------------25
8.2.3. EEPROM contents ----------------------------------25

8.3. How to Clear User Setting------------------------------26

8.3.1. Resetting both base unit and handset----------26
8.3.2. Resetting only handset -----------------------------26

9 Troubleshooting Guide

----------------------------------------

27

9.1. Troubleshooting Flowchart -----------------------------27

9.1.1. Check Power------------------------------------------28
9.1.2. Check Record ----------------------------------------29
9.1.3. Check Playback  -------------------------------------30
9.1.4. Check Battery Charge ------------------------------30
9.1.5. Check Link---------------------------------------------31
9.1.6. Check the RF part -----------------------------------33
9.1.7. Registering a Handset to the Base Unit--------37
9.1.8. Deregistering a Handset ---------------------------37
9.1.9. Check Handset Transmission --------------------38

9.1.10. Check Handset Reception-------------------------38

9.1.11. Check Caller ID --------------------------------------38

9.1.12. Bell Reception ----------------------------------------39

9.1.13. Check TAM Operation (for KX-TGC220

only) ---------------------------------------------------- 39

9.2. Troubleshooting by Symptom (Base Unit and

Charger Unit)---------------------------------------------- 40

9.2.1. Check Point (Base Unit) --------------------------- 40

9.3. Troubleshooting by Symptom (Handset)----------- 42

9.3.1. Check Point (Handset)----------------------------- 42

10 Disassembly and Assembly Instructions

---------------

45

10.1. Disassembly Instructions------------------------------- 45

10.1.1. Base Unit ---------------------------------------------- 45
10.1.2. Handset------------------------------------------------ 48
10.1.3. Charger Unit ------------------------------------------ 49

10.2. How to Replace the Handset LCD------------------- 50

11 Measurements and Adjustments

--------------------------

51

11.1. Equipment Required ------------------------------------ 51
11.2. The Setting Method of JIG----------------------------- 51

11.2.1. Connections (Base Unit) -------------------------- 51
11.2.2. How to install Batch file into P.C. ---------------- 52
11.2.3. Commands-------------------------------------------- 52

11.3. Adjustment Standard (Base Unit) -------------------- 53

11.3.1. Bottom View ------------------------------------------ 53

11.4. The Setting Method of JIG (Handset)--------------- 54

11.4.1. Connections ------------------------------------------ 54
11.4.2. How to install Batch file into P.C. ---------------- 55
11.4.3. Commands-------------------------------------------- 55

11.5. Adjustment Standard (Handset) ---------------------- 56

11.5.1. Component View ------------------------------------ 56

11.6. Things to Do after Replacing IC or X'tal ------------ 57

11.6.1. How to download the data ------------------------ 57

11.7. RF Specification ------------------------------------------ 59

11.7.1. Base Unit ---------------------------------------------- 59
11.7.2. Handset------------------------------------------------ 59

11.8. How to Check the Handset Speaker or

Receiver ---------------------------------------------------- 60

11.9. Frequency Table (MHz)--------------------------------- 60

12 Miscellaneous

----------------------------------------------------

61

12.1. How to Replace the Flat Package IC --------------- 61

12.1.1. Preparation-------------------------------------------- 61
12.1.2. How to Remove the IC----------------------------- 61
12.1.3. How to Install the IC -------------------------------- 62
12.1.4. How to Remove a Solder Bridge ---------------- 62

12.2. How to Replace the Shield Case--------------------- 63

12.2.1. Preparation-------------------------------------------- 63
12.2.2. Caution------------------------------------------------- 63
12.2.3. How to Remove the Shield Case---------------- 63
12.2.4. How to Install the Shield Case ------------------- 64

12.3. Terminal Guide of the ICs, Transistors and

Diodes ------------------------------------------------------ 65

12.3.1. Base Unit ---------------------------------------------- 65
12.3.2. Handset------------------------------------------------ 65

13 Schematic Diagram

--------------------------------------------

67

13.1. For Schematic Diagram -------------------------------- 67

13.1.1. Base Unit (Base Unit (Main))--------------------- 67
13.1.2. Handset (Handset (Main)) ------------------------ 67

13.2. Base Unit (Main) ----------------------------------------- 68

13.2.1. KX-TGC210------------------------------------------- 68
13.2.2. KX-TGC220------------------------------------------- 70

13.3. Base Unit (Operation)----------------------------------- 72

Summary of Contents for KX-TGCA20EX




































































































Reviews:

No comments

Related manuals for KX-TGCA20EX

Larry vs Harry Canopy Assembly Manual preview
Canopy
Brand: Larry vs Harry Pages: 20
NEC NEAX 2000 User Manual preview
NEAX 2000
Brand: NEC Pages: 10
NEC NEAX 2000IVS2 User Manual preview
NEAX 2000IVS2
Brand: NEC Pages: 27
Samsung GALAXY J7 V Manual preview
GALAXY J7 V
Brand: Samsung Pages: 2
Baicells Nova-233 G2 Installation Installation preview
Nova-233 G2
Brand: Baicells Pages: 32
BAFANG C965 Manual preview
C965
Brand: BAFANG Pages: 18
VANPOWERS DP C240.CAN User Manual preview
DP C240.CAN
Brand: VANPOWERS Pages: 23
Gamko FK User Manual preview
FK
Brand: Gamko Pages: 32
Hanlong Unicorn 3001 User Manual preview
Unicorn 3001
Brand: Hanlong Pages: 26
Nailor UNI2-VAV Assembly preview
UNI2-VAV
Brand: Nailor Pages: 6
Warmup UCCG Instructions preview
UCCG
Brand: Warmup Pages: 4
Vega VEGAPULS 62 Specification Sheet preview
VEGAPULS 62
Brand: Vega Pages: 2
Vega DP-1 User Manual preview
DP-1
Brand: Vega Pages: 11
Wavetronix smartsensor advance Installation & Quick Start Manual preview
smartsensor advance
Brand: Wavetronix Pages: 2
X-lite CLEO Installation Instructions preview
CLEO
Brand: X-lite Pages: 5
Lutron Electronics Limelight LL-EXTMOUNT-H Installation preview
Limelight LL-EXTMOUNT-H
Brand: Lutron Electronics Pages: 4
National Instruments 2 SD Card Memory Module NI 9802 Operating Instructions Manual preview
2 SD Card Memory Module NI 9802
Brand: National Instruments Pages: 16
Toro 32in Recycler 30118 Manual preview
32in Recycler 30118
Brand: Toro Pages: 4

Brands by name

Popular brands

Load more brands