Panasonic KX-UTG200 Setup Manual Download

Page: 244 / 412

Value Range

Max. 1024 characters

Note

•

The format must be RFC 1738 compliant, as follows:
"<scheme>://<user>:<password>@<host>:<port>/<url-path>"

–

"<user>" must be less than 127 characters.

–

"<password>" must be less than 127 characters.

–

"<user>:<password>@" may be empty.

–

":<port>" can be omitted if you do not need to specify the
port number.

•

If "{mac}" is included in this URL, it will be replaced with the
unit’s MAC address in lower-case.

•

If "{MAC}" is included in this URL, it will be replaced with the
unit’s MAC address in upper-case.

•

If "{MODEL}" is included in this URL, it will be replaced with the
unit’s model name.

•

If "{fwver}" is included in this URL, it will be replaced with the
unit’s firmware version.

•

If this URL ends with "/" (slash), "sip.cfg" is automatically added
at the end of the URL.
For example,

CFG_MASTER_FILE_PATH="http://host/

dir/"

becomes

CFG_MASTER_FILE_PATH="http://

host/dir/sip.cfg"

Default Value

Empty string

Note

•

The URL specified by your phone system dealer may be preset
in the unit.

5.4 System Settings

5.4.1 Login Account Settings

ADMIN_ID

Value Format

String

Description

Specifies the account ID used to access the Web user interface with
the Administrator account.

Value Range

Max. 16 characters (except ", &, ', :, <, >, and space)

Note

•

An empty string is not allowed.

Default Value

admin

244

Administrator Guide

Document Version 2015-01

5.4.1 Login Account Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Setup Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands