Panasonic KX-UTG200 Setup Manual Download

Page: 262 / 412

Description

Specifies the time (UTC) to determine when the CPE will initiate the
periodic Inform method calls.

Note

•

Each Inform call must occur at this reference time plus or minus
an integer multiple of the "

PERIODIC_INFORM_INTERVAL

This "

PERIODIC_INFORM_TIME

" parameter is used only to set

the "phase" of the periodic Informs. The actual value can be
arbitrarily set far into the past or future.
For example, if "

PERIODIC_INFORM_INTERVAL

" is set to

86400 (one day) and if "

PERIODIC_INFORM_TIME

" is set to

midnight on a certain day, then periodic Informs will occur every
day at midnight, starting from the set date.

•

If the time is set to "unknown time", the start time depends on
the CPE’s settings. However, the
"

PERIODIC_INFORM_INTERVAL

" must still be adhered to.

If absolute time is not available to the CPE, its periodic Inform
behavior must be the same as if the
"

PERIODIC_INFORM_TIME

" parameter was set to the

"unknown time".

•

Time zones other than UTC are not supported.

Value Range

4–32 characters

Default Value

0001-01-01T00:00:00Z (unknown time)

CON_REQ_USER_ID

Value Format

String

Description

Specifies the username used to authenticate an ACS making a
Connection Request to the CPE.

Value Range

Max. 63 characters (except ", &, ', :, <, >, and space)

Default Value

Empty string

CON_REQ_PASS

Value Format

String

Description

Specifies the password used to authenticate an ACS making a
Connection Request to the CPE.

Value Range

Max. 63 characters (except ", &, ', :, <, >, and space)

Default Value

Empty string

ANNEX_G_STUN_ENABLE

Value Format

Boolean

262

Administrator Guide

Document Version 2015-01

5.4.7 Management Server Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Setup Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands